- 您现在的位置：买卖IC网 > Datasheet目录436 > GL100MN3MP1 (Sharp Microelectronics)EMITTER IR 940NM HP 6.0MW SMD Datasheet资料下载
参数资料
| 型号： | GL100MN3MP1 |
| 厂商： | Sharp Microelectronics |
| 文件页数： | 5/10页 |
| 文件大小： | 0K |
| 描述： | EMITTER IR 940NM HP 6.0MW SMD |
| 标准包装： | 1,500 |
| 电流 - DC 正向(If)： | 50mA |
| 波长： | 940nm |
| 正向电压： | 1.5V |
| 视角： | 20° |
| 方向： | 顶视图 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 2-SMD，无引线 |
| 包装： | 带卷 (TR) |
GL100MN3MPx
■ Design Considerations
Design Guidelines
1. Allow for natural degradation of the LED as a result of long continuous operation. This part will have 50 % deg-
radation in output after 5 years of continuous use.
2. This product is not designed to be electromagnetic- and ionized-particle-radiation resistant.
■ Manufacturing Guidelines
Soldering Instructions
1. Sharp recommends soldering no more than once when using solder reflow methods.
2. When using solder reflow methods, follow reflow soldering temperature profile shown in Fig. 4. Sharp recom-
mends checking the process to make sure these parameters are not exceeded; exceeding these parameters
can cause substrate bending or other mechanical stresses leading to debonding of the internal gold wires, or
other similar failure modes.
3. If using an infrared lamp to preheat the parts, such heat sources may cause localized high temperatures in the
part's resin. Be sure to keep the temperature profile within the guidelines shown in Fig. 4.
4. If hand soldering, use temperatures ≤ 260° for ≤ 3 seconds. Do not dip-solder or V PS-solder this part.
5. Do not subject the package to excessive mechanical force during soldering as it may cause deformation or
defects in plated connections. Internal connections may be severed due to mechanical force placed on the pack-
age due to the PCB flexing during the soldering process.
Fig. 4 Reflow Soldering Temperature Profile
240°C MAX.
200°C
1 ~ 4°C/s
165°C MAX.
1 ~ 4°C/s
1 ~ 4°C/s
25°C
10 s MAX.
60 s MAX.
120 s MAX.
90 s MAX.
Cleaning Instructions
1. Confirm this device's resistance to process chemicals before use, as certain process chemicals may affect the
optical characteristics.
2. Solvent cleaning: Solvent temperature should be 45°C or below. Immersion time should be 3 minutes or less.
3. Ultrasonic cleaning: The effect upon devices varies due to cleaning bath size, ultrasonic power output, cleaning
time, PCB size and device mounting circumstances. Sharp recommends testing using actual production condi-
tions to confirm the harmlessness of the ultrasonic cleaning methods.
4. Recommended solvent materials: Ethyl alcohol, Methyl alcohol, and Isopropyl alcohol.
Sheet No.: D1-A00801EN
5
相关PDF资料 |
PDF描述 |
|---|---|
| GL390V | EMITTER IR 950NM 9MW T/H |
| GL4800E0000F | EMITTER IR 950NM 3.0MW TH |
| GL480E00000F | EMITTER IR 950NM 3.0MW TH |
| GL610T | EMITTER IR 950NM .7MW 1608 SMD |
| GLAD.01 | EVALUATION KIT FOR GLA.01 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GL10-RT/32/40A/98A | 制造商:PEPPERL+FUCHS 功能描述:Photoelectric (Automation) 制造商:PEPPERL+FUCHS 功能描述:10mm width frame sensor, M8 conn |
| GL110KA7B115 | 功能描述:固定电感器 11 uH Broadband Inductor RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| GL110-KIT | 制造商:Sola/Hevi-Duty 功能描述:Mating Connector Kit |
| GL1116 | 制造商:GTM 制造商全称:GTM 功能描述:0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator |
| GL1117A | 制造商:GTM 制造商全称:GTM 功能描述:1A Low Dropout Positive Adjustable or Fixed-Mode Regulator |
发布紧急采购，3分钟左右您将得到回复。