- 您现在的位置：买卖IC网 > PDF目录371784 > HCS473PQTP (Microchip Technology Inc.) IC EEPROM SPI BUS 8KBIT 8-SOIC PDF资料下载
参数资料
| 型号： | HCS473PQTP |
| 厂商： | Microchip Technology Inc. |
| 英文描述： | IC EEPROM SPI BUS 8KBIT 8-SOIC |
| 中文描述： | 跳码编码器和转发器 |
| 文件页数： | 21/68页 |
| 文件大小： | 1629K |
| 代理商： | HCS473PQTP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
2002 Microchip Technology Inc.
Preliminary
DS40035C-page 19
HCS473
3.2.1
TRANSPONDER OPTIONS
The following HCS473 configuration options influence
the device behavior when in Transponder mode:
Preamble length select (TPRLS)
LF Demodulator (LFDEMOD)
LF Baud rate select (LFBSL)
Anticollision (ACOL)
Proximity Activation (PXMA)
Intelligent Damping (DAMP)
LC response Enable (LCRSP)
RF response Enable (RFRSP)
Skip Field Acknowledge (SKIPACK)
The following sections describe these options in detail.
3.2.1.1
Transponder Preamble Length
Select (TPRLS)
Data responses through the DATA pin use the format
determined by the Encoder mode options, with one
exception/option to shorten the response time. The
response’s preamble can be reduced to 4 high pulses
by setting the transponder preamble length select
option. This only affects the responses as a result of
transponder communication (proximity activation trans-
missions included), not responses resulting from but-
ton input activations. The 4 high pulse short preamble
will be at the same duty cycle defined by the preamble
duty cycle Encoder mode option (PRD).
TABLE 3-2:
TRANSPONDER PREAMBLE
LENGTH SELECT (TPRLS)
3.2.1.2
LF Demodulator (LFDEMOD)
The HCS473 has a LF Demodulator mode useful for
debugging antenna hardware.
Enabling LFDEMOD limits the device to demodulator
only mode. After receiving an appropriate wake-up
sequence, the device enters a loop demodulating the
signal on the LC pins and outputting the resulting digital
representation on the LED pin. The HCS473 remains in
this mode until no edges are detected on the LC pins
for T
DEMOD
, upon which it will return to Low-power
mode; requiring another wake-up sequence to further
demodulate data.
The demodulated signal on the LED pin is accurate to
within +/-10
μ
s of the signal on the LC pins. The injected
signal will have baud rate limitations based on the
HCS473’s internal filter charge and discharge times,
Section 3.2.6.
The filter times discussed in Section 3.2.6 will be easily
seen in Demodulator mode. The internal filter delay
may be isolated by communicating to the HCS473
inputting the digital signal into LCX and observing the
signal plus internal filter delays on the LED pin.
LFDEMOD options:
Disabled - device functions normally
Enabled - device demodulates signal on LC pins,
outputting digital result on the LED pin.
3.2.1.3
LF Baud Rate Select (LFBSL)
The LF Baud rate select option allows the user to adjust
the basic pulse width element (LF
TE
) used for tran-
sponder communication.
LFBSL options:
100
μ
s LF
TE
200
μ
s LF
TE
400
μ
s LF
TE
800
μ
s LF
TE
All communication to and from the HCS473 through the
LC transponder pins will use the selected LF
TE
. RF
acknowledges to LF communication, through the DATA
pin, will also use the selected LF
TE
.
3.2.1.4
Anticollision (ACOL)
Multiple transponders in the same inductive field will
simultaneously respond to inductive commands.
Enabling anticollision prevents multiple HCS473
responses from 'colliding'. Hence the term ‘anticolli-
sion.’
When anticollision (ACOL) is enabled, the first com-
mand received after the device wakes must be either
the SELECT TRANSPONDER or ANTICOLLISION
OFFcommand before the HCS473 will respond to any
other command.
The ANTICOLLISION OFF command may be used to
temporarily bypass anticollision requirements for a sin-
gle communication sequence. It allows communication
with an anticollision enabled HCS473 if the VID and
TID are not known (perhaps during a learning
sequence). See Section 3.2.3.7 for further anticollision
off details.
The SELECT TRANSPONDER command allows the
addressing of and communication to an individual
HCS473, regardless if multiple devices are in the field
(Section 3.2.3.1).
Note:
The long preamble enable Encoder mode
option (LPRE) holds priority over the tran-
sponder preamble length option.
TPLS
LPRE
Description
0
0
Normal - 16 high pulses
Long - LPRL determines length
Short - 4 high pulses
X
1
1
0
Note:
Damping is disabled when in Demodulator
mode.
相关PDF资料 |
PDF描述 |
|---|---|
| HCS473PROM | IC EEPROM SPI BUS 32KBIT 8-SOIC |
| HCS473PSQTP | Code Hopping Encoder and Transponder |
| HCS473SLQTP | Code Hopping Encoder and Transponder |
| HCS473SLROM | Code Hopping Encoder and Transponder |
| HCS473SLSQTP | Code Hopping Encoder and Transponder |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HCS473-PQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473PROM | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473-PROM | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473PSQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473-PSQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
发布紧急采购，3分钟左右您将得到回复。