参数资料
| 型号： | HIP6007CB-T |
| 厂商： | Intersil |
| 文件页数： | 5/10页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM STD BUCK 14-SOIC |
| 标准包装： | 2,500 |
| 应用： | 控制器，Intel Pentium? Pro、PowerP、Alpha |
| 输入电压： | 2.5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 1.27 V ~ 12 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 管件 |
HIP6007
Functional Description
Initialization
The HIP6007 automatically initializes upon receipt of power.
Special sequencing of the input supplies is not necessary.
The Power-On Reset (POR) function continually monitors
the input supply voltages and the enable (EN) pin. The POR
monitors the bias voltage at the VCC pin and the input
SOFT-START
(1V/DIV)
voltage (V IN ) on the OCSET pin. The level on OCSET is
equal to V IN less a fixed voltage drop (see over-current
protection). With the EN pin held to VCC, the POR function
initiates soft start operation after both input supply voltages
exceed their POR thresholds. For operation with a single
0V
0V
OUTPUT
VOLTAGE
(1V/DIV)
+12V power source, V IN and V CC are equivalent and the
+12V power source must exceed the rising V CC threshold
before POR initiates operation.
t1
t2
TIME (5ms/DIV)
t3
The Power-On Reset (POR) function inhibits operation with
the chip disabled (EN pin low). With both input supplies
above their POR thresholds, transitioning the EN pin high
initiates a soft start interval.
Soft Start
The POR function initiates the soft start sequence. An internal
10 μ A current source charges an external capacitor (C SS ) on
the SS pin to 4V. Soft start clamps the error amplifier output
(COMP pin) and reference input (+ terminal of error amp) to
the SS pin voltage. Figure 3 shows the soft start interval with
C SS = 0.1 μ F. Initially the clamp on the error amplifier (COMP
pin) controls the converter’s output voltage. At t1 in Figure 3,
the SS voltage reaches the valley of the oscillator’s triangle
wave. The oscillator’s triangular waveform is compared to the
ramping error amplifier voltage. This generates PHASE
pulses of increasing width that charge the output capacitor(s).
This interval of increasing pulse width continues to t2. With
sufficient output voltage, the clamp on the reference input
controls the output voltage. This is the interval between t2 and
t3 in Figure 3. At t3 the SS voltage exceeds the reference
voltage and the output voltage is in regulation. This method
provides a rapid and controlled output voltage rise.
FIGURE 3. SOFT-START INTERVAL
Over-Current Protection
The over-current function protects the converter from a
shorted output by using the upper MOSFET’s on-resistance,
r DS(ON) to monitor the current. This method enhances the
converter’s efficiency and reduces cost by eliminating a
current sensing resistor.
The over-current function cycles the soft-start function in a
hiccup mode to provide fault protection. A resistor (R OCSET )
programs the over-current trip level. An internal 200 μ A
(typical) current sink develops a voltage across R OCSET that
is reference to V IN . When the voltage across the upper
MOSFET (also referenced to V IN ) exceeds the voltage
across R OCSET , the over-current function initiates a soft-
start sequence. The soft-start function discharges C SS with
a 10 μ A current sink and inhibits PWM operation. The soft-
start function recharges C SS , and PWM operation resumes
with the error amplifier clamped to the SS voltage. Should an
overload occur while recharging C SS , the soft start function
inhibits PWM operation while fully charging C SS to 4V to
complete its cycle. Figure 4 shows this operation with an
overload condition. Note that the inductor current increases
to over 15A during the C SS charging interval and causes an
over-current trip. The converter dissipates very little power
with this method. The measured input power for the
conditions of Figure 4 is 2.5W.
135
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6012CV-T | IC CTRLR PWM SYNC BUCK 14-TSSOP |
| HIP6013CB-T | IC CONTROLLER PWM BUCK 14-SOIC |
| HIP6301CB | IC REG CTRLR BUCK PWM 20-SOIC |
| HIP6302CB | IC REG CTRLR BUCK PWM 16-SOIC |
| HIP6302VCB-T | IC REG CTRLR BUCK PWM 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6007EVAL1 | 制造商:Intersil Corporation 功能描述:EVAL KIT FOR BUCK PULSE-WIDTH MODULATOR (PWM) CNTRLR - Bulk |
| HIP6008 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6008CB | 制造商:Rochester Electronics LLC 功能描述:PWMCONTROLLER4/BITDACW/4BITDAC1.5%16NBSOIC" - Bulk |
| HIP6008CB-T | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP600ACB | 制造商:Harris Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。