- 您现在的位置：买卖IC网 > PDF目录15074 > HIP6301VCB-T (Intersil)IC REG CTRLR BUCK PWM 20-SOIC PDF资料下载
参数资料
| 型号： | HIP6301VCB-T |
| 厂商： | Intersil |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 20-SOIC |
| 标准包装： | 1,000 |
| PWM 型： | 控制器 |
| 输出数： | 4 |
| 频率 - 最大： | 336kHz |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
HIP6301V, HIP6302V
input. PWM outputs are driven low when the VSEN pin
detects that the CORE voltage is 15% above the
1.85V
programmed VID level. This condition drives the PWM
1.85V
VREF
VCORE
outputs low, causing in the lower or MOSFETs to conduct
and shunt the CORE voltage to ground to protect the load.
If after this event, the CORE voltage falls below the
overvoltage limit (plus some hysteresis), the PWM outputs
will be three state. The HIP6601 family drivers pass the
three state information along, and shuts off both upper and
PGOOD
5.00V
VID CHANGE
5.00V
50μs/DIV
FIGURE 6. VCORE TRACKING THE REFERENCE VOLTAGE
AFTER A 1.85V TO 1.10V CHANGE COMMAND
VCORE
VREF
1.10V
lower MOSFETs. This prevents “dumping” of the output
capacitors back through the lower MOSFETs, avoiding a
possibly destructive ringing of the capacitors and output
inductors. If the conditions that caused the overvoltage still
persist, the PWM outputs will be cycled between three state
and V CORE clamped to ground, as a hysteretic shunt
regulator.
Undervoltage
The VSEN pin also detects when the CORE voltage falls
more than 10% below the VID programmed level. This
causes PGOOD to go low, but has no other effect on
operation and is not latched. There is also hysteresis in this
detection point.
Overcurrent
In the event of an overcurrent condition, the overcurrent
protection circuit reduces the average current delivered to
1.10V
5.00V
PGOOD
less than 25% of the current limit. When an overcurrent
condition is detected, the controller forces all PWM outputs
into a three state mode. This condition results in the gate
driver removing drive to the output stages. The controller
5.00V
VID CHANGE
50μs/DIV
FIGURE 7. VCORE TRACKING THE REFERENCE VOLTAGE
AFTER A 1.10V TO 1.85V CHANGE COMMAND
Fault Protection
The HIP6301V and HIP6302V protect the microprocessor
and the entire power system from damaging stress levels.
Within the controller, both overvoltage and overcurrent
circuits are incorporated to protect the load and regulator.
Overvoltage
The VSEN pin is connected to the microprocessor CORE
voltage. A CORE overvoltage condition is detected when the
VSEN pin goes more than 15% above the programmed VID
level.
The overvoltage condition is latched, disabling normal PWM
operation, and causing PGOOD to go low. The latch can
only be reset by lowering and returning V CC high to initiate a
POR and soft-start sequence.
During a latched overvoltage, the PWM outputs will be
driven either low or three state, depending upon the VSEN
11
goes into a wait delay timing cycle that is equal to the
soft-start ramp time. PGOOD also goes “low” during this time
due to VSEN going below its threshold voltage.To lower the
average output dissipation, the soft-start initial wait time is
increased from 32 to 2048 cycles, then the soft-start ramp is
initiated. At a PWM frequency of 200kHz, for instance, an
overcurrent detection would cause a dead time of 10.24ms,
then a ramp of 10.08ms.
At the end of the delay, PWM outputs are restarted and the
soft-start ramp is initiated. If a short is present at that time,
the cycle is repeated. This is the hiccup mode.
Figure 8 shows the supply shorted under operation and the
hiccup operating mode previously described. Note that due
to the high short circuit current, overcurrent is detected
before completion of the start-up sequence so the delay is
not quite as long as the normal soft-start cycle.
FN9034.3
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| X5163S8IZ-2.7A | IC CPU SUPERV 16K EEPROM 8-SOIC |
| HIP6301VCB | IC REG CTRLR BUCK PWM 20-SOIC |
| RCC22DREH-S93 | CONN EDGECARD 44POS .100 EYELET |
| X5083PIZ-2.7 | IC CPU SUPERV 8K EEPROM 8-PDIP |
| VI-24W-EW-F4 | CONVERTER MOD DC/DC 5.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6301VCB-TS2490 | 制造商:Intersil Corporation 功能描述: |
| HIP6301VCBZ | 功能描述:电流型 PWM 控制器 MULTI-PHS CNTRLR VID ON THE FLYINTEL VID RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| HIP6301VCBZA | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6301VCBZA-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6301VCBZ-T | 功能描述:电流型 PWM 控制器 MULTI-PHS CNTRLR VID ON THE FLYINTEL VID RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。