- 您现在的位置：买卖IC网 > PDF目录371822 > HIP6521EVAL1 (Intersil Corporation) PWM and Triple Linear Power Controller PDF资料下载
参数资料
| 型号： | HIP6521EVAL1 |
| 厂商： | Intersil Corporation |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | PWM and Triple Linear Power Controller |
| 中文描述： | PWM和三线性功率控制器 |
| 文件页数： | 7/13页 |
| 文件大小： | 154K |
| 代理商： | HIP6521EVAL1 |
7
1. The maximum r
DS(ON)
at the highest junction temperature.
2. The minimum I
OCSET
from the specification table.
3. Determine I
PEAK
for I
PEAK
> I
OUT(MAX)
+ (
I)/2, where
I is the output inductor ripple current.
For an equation for the ripple current see the section under
component guidelines titled ‘Output Inductor Selection’.
Output Voltage Selection
The output voltage of the PWM converter can be resistor-
programmed to any level between V
IN
and 0.8V. However,
since the value of R
S1
is affecting the values of the rest of
the compensation components, it is advisable its value is
kept between 2k
and 5k
.
All linear regulators’ output voltages are set by means of
external resistor dividers as shown in Figure 4. The two
resistors used to set the voltage on each of the three linear
regulators have to meet the following criteria: their value
while in a parallel connection has to be less than 5k
, or
otherwise said, the following relationship has to be met:
There may be a second restriction on the size of the
resistors used to set the linear regulators’ output voltage
based on ACPI functionality. Read the ‘ACPI
Implementation’ section under ‘Application Guidelines’ to
see if this additional constraint concerns your application. To
ensure the parallel combination of the feedback resistors
equals a certain chosen value, R
FB
, use the following
equations:
, where
V
OUT
- the desired output voltage,
V
FB
- feedback (reference) voltage, 0.8V.
Application Guidelines
Soft-Start Interval
The soft-start function controls the output voltages rate of rise
to limit the current surge at start-up. The soft-start function is
integrated on the chip and the soft-start interval is thus fixed.
Layout Considerations
MOSFETs switch very fast and efficiently. The speed with
which the current transitions from one device to another
causes voltage spikes across the interconnecting
impedances and parasitic circuit elements. The voltage
spikes can degrade efficiency, radiate noise into the circuit,
and lead to device overvoltage stress. Careful component
layout and printed circuit design minimizes the voltage
spikes in the converter. Consider, as an example, the turn-
off transition of the upper PWM MOSFET. Prior to turn-off,
the upper MOSFET was carrying the full load current.
During the turn-off, current stops flowing in the upper
MOSFET and is picked up by the lower MOSFET or
Schottky diode. Any inductance in the switched current
path generates a large voltage spike during the switching
interval. Careful component selection, tight layout of the
critical components, and short, wide circuit traces minimize
the magnitude of voltage spikes. See the Application Note
AN9908 for evaluation board drawings of the component
placement and printed circuit board.
There are two sets of critical components in a DC-DC
converter using a HIP6521 controller. The switching power
components are the most critical because they switch large
amounts of energy, and as such, they tend to generate
UGATE
OCSET
PHASE
OCC
+
-
GATE
CONTROL
VCC
OC
40
μ
A
V
DS(ON)
i
D
V
SET
R
OCSET
V
IN
= +5V
OVERCURRENT TRIP:
VDS
I
OCSET
+
+
FIGURE 3. OVERCURRENT DETECTION
PWM
DRIVE
iD
rDS ON
(
)
×
IOCSET
ROCSET
×
>
VSET
>
VPHASE
VOCSET
VIN
VIN
VDS
VSET
–
=
–
=
DRIVE3
FB3
FB4
C
OUT4
C
OUT3
Q4
HIP6521
V
OUT3
V
OUT4
Q5
3.3V
IN
DRIVE4
R
S3
R
P3
R
S4
R
P4
VOUT
0.8
1
RP
+
×
=
FIGURE 4. ADJUSTING THE OUTPUT VOLTAGE OF ANY OF
THE FOUR REGULATORS (OUTPUTS 3 AND 4
PICTURED)
+
+
R
S
R
P
R
P
×
+
---------------------
5k
<
R
S
V
FB
---------------
R
FB
×
=
R
P
R
OUT
V
FB
×
------------------–
=
HIP6521
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6602BCRZ-T | Dual Channel Synchronous Rectified Buck MOSFET Driver |
| HIP6602BCRZA | Dual Channel Synchronous Rectified Buck MOSFET Driver |
| HIP6602BCRZA-T | Dual Channel Synchronous Rectified Buck MOSFET Driver |
| HIP6602B | Dual Channel Synchronous Rectified Buck MOSFET Driver |
| HIP6602BCBZ-T | Dual Channel Synchronous Rectified Buck MOSFET Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6601 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Synchronous-Rectified Buck MOSFET Drivers |
| HIP6601_04 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Synchronous-Rectified Buck MOSFET Drivers |
| HIP6601A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Synchronous Rectified Buck MOSFET Drivers |
| HIP6601ACB | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Synchronous Rectified Buck MOSFET Drivers |
| HIP6601ACB-T | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。