- 您现在的位置：买卖IC网 > PDF目录18812 > HMC1002-TR (Honeywell Microelectronics & Precision Sensors)SENSOR LINEAR MAGN 2AXIS 20-SOIC PDF资料下载
参数资料
| 型号： | HMC1002-TR |
| 厂商： | Honeywell Microelectronics & Precision Sensors |
| 文件页数： | 8/15页 |
| 文件大小： | 1409K |
| 描述： | SENSOR LINEAR MAGN 2AXIS 20-SOIC |
| 产品培训模块： | Magnetic Sensors |
| 标准包装： | 1 |
| 传感范围： | ±2g |
| 类型： | 线性 |
| 电源电压： | 5 V ~ 12 V |
| 输出类型： | 差分电压 |
| 特点： | 罗盘 - 双轴 |
| 工作温度： | -55°C ~ 150°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 散装 |
| 产品目录页面： | 2814 (CN2011-ZH PDF) |
| 其它名称： | 342-1070 342-1070-1 342-1070-ND |
HMC1001/1002/1021/1022
8 ww.hone well.com
SET/RESET STRAP OPERATION
The reasons to perform a set or reset on an AMR sensor are: 1) To recover from a strong external magnetic field that
likely has re-magnetized the sensor, 2) to optimize the magnetic domains for most sensitive performance, and 3) to flip
the domains for extraction of bridge offset under changing temperature conditions.
Strong external magnetic fields that exceed a 10 to 20 gauss disturbing field limit, can come from a variety of sources.
The most common types of strong field sources come from permanent magnets such as speaker magnets, nearby high-
current conductors such as welding cables and power feeder cables, and by magnetic coils in electronic equipment such
as CRT monitors and power transformers. Magnets exhibit pole face strengths in hundreds to thousands of gauss. These
high intensity magnetic field sources do not permanently damage the sensor elements, but the elements will be disturbed
to the exposed fields rather than the required easy axis directions. The result of this re-magnetization of the sensor
elements, the sensor will lack sensitivity or indicate a stuck sensor output. Using the set and reset pulses will
magnetically restore the sensor.
AMR sensors are also ferromagnetic devices with a crystalline structure. This same thin film structure that makes the
sensor sensitive to external magnetic fields also has the downside that changing magnetic field directions and thermal
energy over time will increase the self-noise of the sensor elements. This noise, while very small, does impair the
accurate measurement of sub-milligauss field strengths or changes in field strength in microgauss increments. By
employing frequent set and reset fields on the sensor, the self-noise will be to its lowest possible level.
As the sensor element temperature changes, either due to self-heating or external environments, each elements
resistance will change in proportion to the temperature. One way to eliminate the bridge offset voltage is to make stable
magnetic field measurements of the bridge output voltage in between each set and reset field application. Since the
external field components of the bridge output voltage will flip polarity, the set and reset bridge output voltages can be
subtracted and the result divided by two to calculate the bridge offset. See application note AN212 for the details on
bridge offset voltage computation and correction.
SET/RESET DRIVE CIRCUITS
The above description explained that providing pulses of electrical current creates the needed magnetic fields to realign
the magnetic domains of the sensor resistive elements. Also the rationale for performing these set and reset pulses has
been justified. The following paragraphs shall show when and how to apply these pulsed currents, and circuits to
implement them. Figure 2 shows a simplistic schematic of a set/reset circuit.
These set and reset pulses are shown in Figure 2 as dampened exponential pulse waveforms because the most popular
method of generating these relatively high current, short duration pulses is via a capacitive charge and dump type of
circuit. Most electronics, especially in consumer battery powered devices, do not have the capability to supply these high
current pulses from their existing power supply sources. Thus Vsr is actually a charged up capacitor that is suddenly
switched across the set/reset strap. The value of this capacitor is usually a couple hundred nano-Farads (稦) to a few
micro-Farads (礔) depending on the strap resistance to be driven. The decay of the exponential waveform will mostly be
governed by a time constant (?or Tau) that is the capacitance in farads multiplied by the resistance, and is measured in
seconds.
Figure 2 A Simple Set/Reset Circuit
1
Vsr
Rsr
5
Iset
Ireset
Strap
Resistance
Set/Reset
Pulse Source
S/R+
S/R-
?SPAN class="pst HMC1001-RC_2174751_7">= R*C = ~2?SPAN class="pst HMC1001-RC_2174751_7">sec
1
Vsr
Rsr
5
Iset
Ireset
Strap
Resistance
Set/Reset
Pulse Source
S/R+
S/R-
?SPAN class="pst HMC1001-RC_2174751_7"> = R*C = ~2?SPAN class="pst HMC1001-RC_2174751_7">sec
相关PDF资料 |
PDF描述 |
|---|---|
| P2Z7ACB700W12 | SCR MOD PWR-BRIK 1200V 395A |
| 7C-33.3330MBA-T | OSC 33.3330 MHZ 3.3V SMT |
| R9G00212XX | RECTIFIER 200V 1200A |
| 9111-60 BLK | PATCHCORD BANA PLUG STKG 60" BLK |
| PA432006 | SCR MOD AC-SW ISO 2000V 600A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMC1010LP4E | 制造商:Hittite Microwave Corp 功能描述:RF RMS PWR DETECTOR 3.9GHZ 24SMT |
| HMC1010LP4ETR | 功能描述:RF Detector IC General Purpose 0Hz ~ 3.9GHz -50dBm ~ 10dBm ±1dB 24-VFQFN Exposed Pad 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 频率:0Hz ~ 3.9GHz RF 类型:通用 输入范围:-50dBm ~ 10dBm 精度:±1dB 电压 - 电源:4.5 V ~ 5.5 V 电流 - 电源:50mA 封装/外壳:24-VFQFN 裸露焊盘 标准包装:1 |
| HMC1013LP4E | 制造商:Hittite Microwave Corp 功能描述:IC AMP SDLVA 67DB 24SMD |
| HMC1014 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs pHEMPT MMIC 0.5 Watt |
| HMC1015 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs MMIC Fundam ental Mixer, 26 - 32 GHz |
发布紧急采购，3分钟左右您将得到回复。