- 您现在的位置：买卖IC网 > PDF目录65470 > HMC903 (HITTITE MICROWAVE CORP) 6000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | HMC903 |
| 厂商： | HITTITE MICROWAVE CORP |
| 元件分类： | 放大器 |
| 英文描述： | 6000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| 封装： | 1.33 X 1.08 MM, 0.10 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SMT, GP-2, 6 PIN |
| 文件页数： | 6/6页 |
| 文件大小： | 671K |
| 代理商： | HMC903 |
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
A
m
p
li
f
ie
r
s
-
lo
w
N
o
is
e
-
s
m
T
7
7 - 6
HMC903
v00.0310
GaAs pHEMT MMIC LOW NOISE
AMPLIFIER, 6 - 18 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HmC general Handling, mounting, Bonding Note).
50 ohm microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing rf to and from the chip
(figure 1). if 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. one way to accom-
plish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (figure 2).
microstrip substrates should be placed as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either waffle or Gel based esD protec-
tive containers, and then sealed in an esD protective bag for shipment.
once the sealed esD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. Do NoT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity: follow esD precautions to protect against esD
strikes.
Transients: suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pick-
up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The
surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with Ausn eutectic preforms or with electrically conductive epoxy.
The mounting surface should be clean and flat.
eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool
temperature of 265 °C. when hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. Do
NoT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of
scrubbing should be required for attachment.
epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
rf bonds made with two 1 mil wires are recommended. These bonds should be thermosonically bonded with a force
of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds
should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a
nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable
bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm).
0.254mm (0.010”) Thick MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
相关PDF资料 |
PDF描述 |
|---|---|
| HMC907LP5E | 200 MHz - 22000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC913LC4B | 600 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC930 | 0 MHz - 40000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| HMC942LP4E | 12500 MHz - 15500 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| HMC962LC4 | 7500 MHz - 26500 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMC903LP3E | 功能描述:IC AMP MMIC GAAS LN 16QFN RoHS:是 类别:RF/IF 和 RFID >> RF 放大器 系列:- 标准包装:3,000 系列:- 频率:100MHz ~ 6GHz P1dB:9.14dBm（8.2mW） 增益:15.7dB 噪音数据:1.3dB RF 型:CDMA，TDMA，PCS 电源电压:2.7 V ~ 5 V 电流 - 电源:60mA 测试频率:2GHz 封装/外壳:0505（1412 公制） 包装:带卷 (TR) |
| HMC903LP3ETR | 制造商:Hittite Microwave Corp 功能描述:IC AMP MMIC GAAS LN 16QFN |
| HMC903-SX | 功能描述:IC RF AMP LN DIE 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:在售 频率:6GHz ~ 18GHz P1dB:16dBm 增益:19dB 噪声系数:1.6dB RF 类型:通用 电压 - 电源:3.5V 电流 - 电源:90mA 测试频率:6GHz ~ 18GHz 封装/外壳:模具 供应商器件封装:模具 标准包装:2 |
| HMC904LC5 | 制造商:Hittite Microwave Corp 功能描述:IC MMIC I/Q DOWNCONV 32SMD |
| HMC905LP3E | 制造商:Hittite Microwave Corp 功能描述:IC DIVIDER BICMOS SIGE LN 16-QFN |
发布紧急采购，3分钟左右您将得到回复。