- 您现在的位置：买卖IC网 > PDF目录370643 > HMP8112EVAL2 (Harris Corporation) NTSC/PAL Video Decoder PDF资料下载
参数资料
| 型号： | HMP8112EVAL2 |
| 厂商： | Harris Corporation |
| 英文描述： | NTSC/PAL Video Decoder |
| 中文描述： | NTSC / PAL视频解码器 |
| 文件页数： | 10/40页 |
| 文件大小： | 563K |
| 代理商： | HMP8112EVAL2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
10
flag, when asserted, tells the user that the video standard
that was expected was not found and a different standard
should be selected in the Video Input Control register. The
error flag is cleared after a RESET or after the Chroma PLL
Clock Ratio register has been loaded via the I
2
C bus. After
the flag is cleared the standard error logic verifies the video
standard. The error flag is set after 2 vertical sync periods
have passed and the line count did not match the expected
line count.
Video Adjustments
The HMP8112 allows the user to vary such video parame-
ters as Contrast, Brightness, Sharpness, Hue and Color Sat-
uration. These adjustments can be made via the I
2
C
interface. Contrast, brightness and sharpness are luminance
controls. The full dynamic range of the luminance channel
can be used by selecting the IRE setup cancellation mode.
This mode will remove the IRE setup and blanking level off-
set to take advantage of the full dynamic range of the lumi-
nance processing path. The sharpening filters allow the
enhancement of low, mid and high frequency components of
the luminance signal to compensate for low amplitude video.
Vertical sharpness is also controlled via the I
2
C interface.
Hue and Color saturation controls enhance the CbCr com-
ponents of the incoming video, all under user control.
Luminance Adjustments
The Luminance data can be adjusted in the HMP8112. The
user can adjust brightness and contrast of the Y or lumi-
nance data. The user can also set the IRE or setup subtrac-
tion value to eliminate the black pedestal offset from NTSC
signals. The Contrast adjustment range can exceed a value
of one so as to take full advantage of the 8-bit dynamic
range for Y. The user control settings executes the equation
Y
OUT
= (Y - IRE Setup + BRIGHTNESS) x CONTRAST
Brightness
The user can control the brightness of the incoming video by
programming the Brightness register. The brightness adjust-
ment will offset the Y component. The brightness register is
an 8-bit register where the bottom 7 bits are brightness con-
trol and the top bit is the IRE setup. The IRE setup for NTSC
is 70 and the setup for PAL is 63.
When the IRE bit is set (1) then the value of 70 is subtracted
from the Y data, and if the IRE bit is cleared (0) then the val-
ues of 63 is subtracted. The brightness control bits BR[6-0]
will brighten the picture as the value is increased. BR = -64
is the darkest and BR = +63 is the brightest. The default
value of the register after a RESET is 0 (80
H
).
Contrast
The contrast adjustment will allow the user to increase and
decrease the gain of the Y data. The contrast factor is an 8-bit
number (as shown below) that ranges from 0 to 1.999.
X.XXXXXXX
The default value after a RESET is 1.47 (BD
H
).
Hue or Tint Adjust
The Hue adjustment is applied to the U and the V color differ-
ence signal. The Hue adjusts the phase of the given UV data.
The Hue can be adjusted by
±
30
o
in 1/4
o
increments. This is
achieved by changing the Burst Phase Locked reference
point. Figure 10 shows the block diagram for the color adjust-
ment section. This default value for this register is 0 (00
H
).
Horizontal/Vertical Sharpness
The frequency characteristics of the video waveform can be
altered to enhance the sharpness of the picture. The Horizontal
Sharpness register acts as a 4 band equalizer where the ampli-
tude of specific frequency ranges can be enhanced or dimin-
ished. The Sharpness Control Register allows the Low (LF),
Mid (MF) and High Frequency (HF) bands of the luminance sig-
nal to be enhanced. Vertical Sharpness can be adjusted to 1 or
a factor of 0. The RESET default is a factor of 1.0
TABLE 3. USER CONTROLLED SETTINGS
USER VIDEO SETTINGS
Brightness
Contrast
Hue or Tint
Horizontal Sharpness
Vertical Sharpness
Color Saturation
IRE BLACK SETUP
(NTSC = 70, PAL = 63)
+
+
-
X
BRIGHTNESS
(-64 TO +63)
CONTRAST
(0 TO 1.999)
Y DATA
FROM
DECODER
Y’
8
FIGURE 9. LUMINANCE CONTROL SETTINGS PATH
DEMODULATED
UV DATA
UV DATA
VIDEO
DATA
HUE OFFSET
HUE
ADJUST
+
TO INPUT SAMPLE
RATE
CONVERTER
LOOP
CHROMA
PHASE LOCKED
COLOR
DECODER
CHROMA
AGC AND
USER
SETTINGS
FIGURE 10. HUE ADJUST BLOCK DIAGRAM
HMP8112
相关PDF资料 |
PDF描述 |
|---|---|
| HMP8156EVAL2 | NTSC/PAL Video Decoder |
| HMP8156EVAL1 | NTSC/PAL Encoders |
| HMP8156EVAL2 | NTSC/PAL Encoders |
| HMP8156 | NTSC/PAL Encoder |
| HMP8156ACN | NTSC/PAL Encoders |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMP8115 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8115CN | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8116 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8116CN | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
| HMP8117 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:NTSC/PAL Video Decoder |
发布紧急采购，3分钟左右您将得到回复。