- 您现在的位置：买卖IC网 > PDF目录20240 > ICL7136CM44Z (Intersil)IC ADC 3.5DIGIT LOW PWR 44-MQFP PDF资料下载
参数资料
| 型号： | ICL7136CM44Z |
| 厂商： | Intersil |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC ADC 3.5DIGIT LOW PWR 44-MQFP |
| 标准包装： | 96 |
| 显示器类型： | LCD |
| 配置： | 7 段显示 |
| 数字或字符： | A/D，3.5 位数字 |
| 电流 - 电源： | 70µA |
| 电源电压： | 9V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-QFP |
| 供应商设备封装： | 44-MQFP（10x10） |
| 包装： | 托盘 |
ICL7136
Analog COMMON
This pin is included primarily to set the common mode
V+
voltage for battery operation or for any system where the
input signals are floating with respect to the power supply.
The COMMON pin sets a voltage that is approximately 2.8V
more negative than the positive supply. This is selected to
give a minimum end-of-life battery voltage of about 6.8V.
However, analog COMMON has some of the attributes of a
reference voltage. When the total supply voltage is large
enough to cause the zener to regulate (>7V), the COMMON
voltage will have a low voltage coefficient (0.001%/V), low
output impedance ( ? 15 ? ), and a temperature coefficient
typically less than 150ppm/ o C.
V
REF HI
REF LO
ICL7136
FIGURE 3A.
V-
6.8V
ZENER
I Z
The limitations of the on chip reference should also be
recognized, however. Due to their higher thermal resistance,
V+
plastic parts are poorer in this respect than ceramic. The
combination of reference Temperature Coefficient (TC), internal
chip dissipation, and package thermal resistance can increase
noise near full scale from 25 μ V to 80 μ V P-P . Also the linearity in
going from a high dissipation count such as 1000 (20 segments
on) to a low dissipation count such as 1111 (8 segments on) can
suffer by a count or more. Devices with a positive TC reference
may require several counts to pull out of an over range
condition. This is because over-range is a low dissipation
V
ICL7136
REF HI
REF LO
COMMON
20k ?
6.8k ?
ICL8069
1.2V
REFERENCE
mode, with the three least significant digits blanked. Similarly,
units with a negative TC may cycle between over range and a
non-over range count as the die alternately heats and cools. All
these problems are of course eliminated if an external
reference is used.
The ICL7136, with its negligible dissipation, suffers from
none of these problems. In either case, an external
reference can easily be added, as shown in Figure 3.
Analog COMMON is also used as the input low return during
auto-zero and de-integrate. If IN LO is different from analog
COMMON, a common mode voltage exists in the system
and is taken care of by the excellent CMRR of the converter.
FIGURE 3B.
FIGURE 3. USING AN EXTERNAL REFERENCE
TEST
The TEST pin serves two functions. On the ICL7136 it is
coupled to the internally generated digital supply through a
500 ? resistor. Thus it can be used as the negative supply for
externally generated segment drivers such as decimal points
or any other presentation the user may want to include on
the LCD display. Figures 4 and 5 show such an application.
No more than a 1mA load should be applied.
However, in some applications IN LO will be set at a fixed
known voltage (power supply common for instance). In this
application, analog COMMON should be tied to the same
point, thus removing the common mode voltage from the
converter. The same holds true for the reference voltage. If
V+
ICL7136
1M ?
TO LCD
DECIMAL
POINT
reference can be conveniently tied to analog COMMON, it
should be since this removes the common mode voltage
from the reference system.
Within the lC, analog COMMON is tied to an N-Channel FET
BP
TEST
21
37
TO LCD
BACKPLANE
that can sink approximately 3mA of current to hold the
voltage 2.8V below the positive supply (when a load is trying
to pull the common line positive). However, there is only
10 μ A of source current, so COMMON may easily be tied to a
more negative voltage thus overriding the internal reference.
8
FIGURE 4. SIMPLE INVERTER FOR FIXED DECIMAL POINT
The second function is a “lamp test”. When TEST is pulled
high (to V+) all segments will be turned on and the display
should read “-1888”. The TEST pin will sink about 5mA
under these conditions.
CAUTION: On the ICL7136, in the lamp test mode, the segments have a
constant DC voltage (no square-wave) and may burn the LCD
display if left in this mode for several minutes.
FN3086.6
July 21, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| IDT71V25761S200PF8 | IC SRAM 4MBIT 200MHZ 100TQFP |
| PSA15R-120PV-R-CR3 | ADAPTER WALL R-SERIES 15W 12V |
| MMSD914T1 | DIODE SWITCH 100V SOD123 |
| IDT71V25761S200PF | IC SRAM 4MBIT 200MHZ 100TQFP |
| ICL7107CM44Z | IC ADC 3.5DIGIT LCD/LED 44MQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICL7136CM44ZT | 功能描述:LCD 驱动器 W/ANNEAL ADC 3 5 DIG LW PWR 7106 COM RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| ICL7136CMH | 制造商:Maxim Integrated Products 功能描述:LOW POWER, 3 1/2 DIGIT ADC WITH DIRECT LCD DR - Bulk |
| ICL7136CMH+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL DUAL SLOPE 3 1/2DIGIT LCD 44MQFP - Rail/Tube |
| ICL7136CMH+D | 功能描述:模数转换器 - ADC Low-Pwr 3 1/2 Digit ADC w/Direct LCD Dvr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ICL7136CMH+T | 制造商:Maxim Integrated Products 功能描述:ADC SGL DUAL SLOPE 3 1/2DIGIT LCD 44MQFP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。