- 您现在的位置：买卖IC网 > PDF目录1923 > ICS1893AFILF (IDT, Integrated Device Technology Inc)PHYCEIVER LOW PWR 3.3V 48-SSOP PDF资料下载
参数资料
| 型号： | ICS1893AFILF |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 109/136页 |
| 文件大小： | 0K |
| 描述： | PHYCEIVER LOW PWR 3.3V 48-SSOP |
| 标准包装： | 30 |
| 系列： | PHYceiver™ |
| 类型： | PHY 收发器 |
| 规程： | MII |
| 电源电压： | 3.14 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-BSSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 48-SSOP |
| 包装： | 管件 |
| 其它名称： | 1893AFILF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页当前第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
ICS1893AF, Rev D 10/26/04
October, 2004
74
Chapter 8
Management Register Set
ICS1893AF Data Sheet - Release
Copyright 2004, Integrated Circuit Systems, Inc.
All rights reserved.
8.6.5
Technology Ability Field (bits 4.9:5)
When its Auto-Negotiation sublayer is enabled, the ICS1893AF transmits its link capabilities to its remote
link partner during the auto-negotiation process. The Technology Ability Field (TAF) bits 4.12:5 determine
the specific abilities that the ICS1893AF advertises. The ISO/IEC specification defines the TAF
technologies in Annex 28B.
The ISO/IEC specification reserves bits 4.12:10 for future use. When each of these reserved bits is:
Read by an STA, the ICS1893AF returns a logic zero
Written to by an STA, the STA must use the default value specified in this data sheet
ICS uses some reserved bits to invoke auxiliary functions. To ensure proper operation of the ICS1893AF,
an STA must maintain the default value of these bits. Therefore, ICS recommends that an STA always write
the default value of any reserved bits during all management register write operations.
Reserved bits 4.12:10 are Command Override Write (CW) bits. Whenever bit 16.15 (the Command
Register Override bit) is logic:
Zero, the ICS1893AF isolates all STA writes to CW bits, including bits 4.12:10.
One, an STA can modify the value of bits 4.12:10
Each of the bits 4.9:5 in the TAF represent a specific technology capability. When one of these bits is logic:
Zero, it indicates to the remote link partner that the local device cannot support the technology
represented by the bit.
One, it indicates to the remote link partner that the local device can support the technology.
With the exception of bit 4.9, the default settings of the TAF bits depend on the ICS1893AF operating
mode. Bit 4.9 is always logic zero, indicating that the ICS1893AF cannot support 100Base-T4 operations.
The TAF bits are Command Override Write bits. The default value of these bits depends on the signal level
on the HW/SW pin and whether the Auto-Negotiation sublayer is enabled.
With the Auto-Negotiation Enable bit (bit 0.12) set to logic:
Zero (that is, disabled), the ICS1893AF does not execute the auto-negotiation process. Upon completion
of the initialization sequence, the ICS1893AF proceeds to the Idle state and begins transmitting IDLES.
Two Control Register bits – the Data Rate Select bit (bit 0.13) and the Duplex Select bit (bit 0.8) –
determine the technology mode that the ICS1893AF uses for data transmission and reception. In this
mode, the values of the TAF bits (bits 4.8:5) are undefined.
One (that is, enabled), the ICS1893AF executes the auto-negotiation process and advertises its
capabilities to the remote link partner. The TAF bits (bits 4.8:5) determine the capabilities that the
ICS1893AF advertises to its remote link partner. For the ICS1893AF, all of these bits 4.8:5 are set to
logic one, indicating the ability of the ICS1893AF to provide these technologies.
Note:
1.
The ICS1893AF does not alter the value of the Status Register bits based on the TAF bits in
register 4, as the ISO/IEC definitions for the Status Register bits require these bits to indicate all the
capabilities of the ICS1893AF.
2.
The STA can alter the default TAF bit settings, 4.12:5, and subsequently issue an Auto-Negotiation
Restart.
相关PDF资料 |
PDF描述 |
|---|---|
| ICS1893BFILF | PHYCEIVER LOW PWR 3.3V 48-SSOP |
| ICS1894KI-32LF | PHYCEIVER LOW PWR 3.3V 32QFN |
| ICS1894KI-40LFT | PHYCEIVER LOW PWR 3.3V 40QFN |
| ID82C55A | IC I/O EXPANDER 24B 40DIP |
| ID82C82 | IC DRIVER BUS OCT LATCHING 20DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS1893AFILFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:PHYceiver™ 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ICS1893AFIT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:PHYceiver™ 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ICS1893AFLF | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:PHYceiver™ 标准包装:1 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:4.5 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:剪切带 (CT) 其它名称:ISL31470EIBZ-T7ACT |
| ICS1893AFLFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:PHYceiver™ 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ICS1893AFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:PHYceiver™ 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。