- 您现在的位置：买卖IC网 > PDF目录67685 > ICS2059GI-02 (INTEGRATED DEVICE TECHNOLOGY INC) 27 MHz, VIDEO CLOCK GENERATOR, PDSO16 PDF资料下载
参数资料
| 型号： | ICS2059GI-02 |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 27 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| 封装： | 0.173 INCH, TSSOP-16 |
| 文件页数： | 9/12页 |
| 文件大小： | 309K |
| 代理商： | ICS2059GI-02 |
Clock Multiplier and Jitter Attenuator
MDS 2059-02 C
6
Revision 031605
Integrated Circuit Systems, Inc.
● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
ICS2059-02
In most cases the load capacitors will not be required.
They should not be stuffed on the prototype evaluation
board as the indiscriminate use of these trim capacitors
will typically cause more crystal centering error than
their absence. If the need for the load capacitors is later
determined, the values will fall within the 1-4 pf range.
The need for, and value of, these trim capacitors can
only be determined at prototype evaluation. Please
refer to MAN05 for the procedure to determine the
component values.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed. Please also refer to the Recommended PCB
Layout drawing on page 7.
1) Each 0.01F decoupling capacitor should be
mounted on the component side of the board as close
to the VDD pin as possible. No vias should be used
between decoupling capacitor and VDD pin. The PCB
trace to VDD pin should be kept as short as possible,
as should the PCB trace to the ground via. Distance of
the ferrite bead and bulk decoupling from the device is
less critical.
2) The loop filter components must also be placed
close to the CHGP and VIN pins. CP should be closest
to the device. Coupling of noise from other system
signal traces should be minimized by keeping traces
short and away from active signal traces. Use of vias
should be avoided.
3) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
4) To minimize EMI, the 33
series termination resistor
(if needed) should be placed close to the clock output.
5) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers (the ferrite bead and bulk decoupling
capacitor can be mounted on the back). Other signal
traces should be routed away from the ICS2059-02.
This includes signal traces just underneath the device,
or on layers adjacent to the ground plane layer used by
the device.
The ICS Applications Note MAN05 may also be
referenced for additional suggestions on layout of the
crystal section.
ICS2059-02
Clock Multiplier and Jitter Attenuator
TSD
IDT / ICS Clock Multiplier and Jitter Attenuator
ICS2059-02
6
相关PDF资料 |
PDF描述 |
|---|---|
| ICS2304NZGI-1T | 2304 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| ICS2304NZG-1LF | 2304 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| ICS252MI-XXLF | 200 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| ICS252MI-XX | 200 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| ICS252PMI | 200 MHz, OTHER CLOCK GENERATOR, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS2059GI-02LF | 功能描述:IC CLK MULT/JITTER ATTEN 16TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:1,000 系列:- 类型:时钟/频率合成器，扇出分配 PLL:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 除法器/乘法器:- 电源电压:- 工作温度:- 安装类型:表面贴装 封装/外壳:56-VFQFN 裸露焊盘 供应商设备封装:56-VFQFP-EP（8x8） 包装:带卷 (TR) 其它名称:844S012AKI-01LFT |
| ICS2059GI-02LFT | 功能描述:IC CLK MULT/JITTER ATTEN 16TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| ICS2059GI-02T | 功能描述:IC CLK MULT/JITTER ATTEN 16TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS2101M | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| ICS2101N | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
发布紧急采购，3分钟左右您将得到回复。