- 您现在的位置：买卖IC网 > PDF目录65529 > ICS527R-04 (INTEGRATED DEVICE TECHNOLOGY INC) 527 SERIES, PLL BASED CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 PDF资料下载
参数资料
| 型号： | ICS527R-04 |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟及定时 |
| 英文描述： | 527 SERIES, PLL BASED CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| 封装： | 0.150 INCH, 0.025 INCH PITCH, MO-153, SSOP-28 |
| 文件页数： | 3/9页 |
| 文件大小： | 212K |
| 代理商： | ICS527R-04 |
ICS527-04
CLOCK SLICER USER CONFIGURABLE PECL INPUT ZDB
PECL ZDB AND MULTIPLIER/DIVIDER
IDT / ICS CLOCK SLICER USER CONFIGURABLE PECL INPUT ZDB
3
ICS527-04
REV E 092209
External Components
Decoupling Capacitors
The ICS527-04 requires two 0.01
F decoupling
capacitors to be connected between VDD and GND,
one on each side of the chip. They must be connected
close to the device to minimize lead inductance. The
output levels can be adjusted for different output and
load impedances. Refer to application note MAN09 for
more information on the RES and resistor network
values for the output clocks.
PECL Termination Networks
The PECLO to FBPECL and PECLO to FBPECL
connections should be made directly underneath the
device, unless feedback is being routed through other
devices. The resistor divider networks should be placed
as close to the outputs as possible.
Typical 50
termination is shown in the Block Diagram
on page 1. For other termination schemes, see
MAN09.pdf.
Eliminating the Delay Through Buffers or
Other Components
More complicated feedback schemes can be used,
such as incorporating low skew, multiple output buffers
in the feedback path. An example of this is given later in
the datasheet. The fundamental property of the
ICS527-04 is that it aligns rising edges on CLKIN and
FBPECL at a ratio determined by the reference and
feedback dividers. This means that any delay in the
feedback path will cause the PECL output edge to lead
PECLIN by the delay amount. So, by taking the PECL
output from another device as the input to FBPECL, the
delay through the other device can be eliminated.
Setting the Clock Slicer
Use IRANGE to select the input frequency range. If
either the PECLIN or FBPECL pair frequencies are
greater than (or equal to) 80 MHz, connect IRANGE to
VDD, or let it float. If both frequencies are less than 80
MHz, connect IRANGE to ground.
Choose S1 and S0 from the table on page 2, depending
on the output frequency.
Finally, the divider settings should be selected.
Following is a description of how the dividers should be
set.
Determining ICS527-04 Divider Settings
The user has full control in setting the desired output
clock over the range shown in the table on page 2. The
user should connect the divider select input pins directly
to ground (or VDD, although this is not required
because of internal pull-ups) during Printed Circuit
Board layout, so that the ICS527-04 automatically
produces the correct clock when all components are
soldered. It is also possible to connect the inputs to
parallel I/O ports in order to switch frequencies. The
configuration inputs: IRANGE, S1, S0, R6...0, F6...0 are
compatible with CMOS or TTL levels.
The output of the ICS527-04 can be determined by the
following simple equation:
Where:
Reference Divider Word (RDW) = 0 to 127
Feedback Divider Word (FDW) = 0 to 127
FB Frequency is the same as the output
frequency
Additionally, the following operating ranges should be
observed:
S1 and S0 should be selected depending on the
output frequency. The table on page 2 gives the
ranges.
The dividers are expressed as integers. For example, if
a 50 MHz output on CLK1 is desired from a 40 MHz
input, the reference divider word (RDW) should be 2
and the feedback divider word (FDW) should be 3 which
gives the required 5/4 multiplication. If multiple choices
FB Frequency
Input Frequency
FDW
2
+
RDW
2
+
------------------------
×
=
300kHz
Input Frequency
RDW
2
+
-------------------------------------------
<
相关PDF资料 |
PDF描述 |
|---|---|
| ICS541MT | PLL BASED CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| ICS544MI-01 | 156 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| ICS544M-01LF | 156 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| ICS544MI-01T | 156 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| ICS554-01DPK | 156 MHz, OTHER CLOCK GENERATOR, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS527R-04LF | 功能描述:IC CLK SLICER PECL ZDB 28-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:1,000 系列:- 类型:时钟/频率合成器，扇出分配 PLL:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 除法器/乘法器:- 电源电压:- 工作温度:- 安装类型:表面贴装 封装/外壳:56-VFQFN 裸露焊盘 供应商设备封装:56-VFQFP-EP（8x8） 包装:带卷 (TR) 其它名称:844S012AKI-01LFT |
| ICS527R-04LFT | 功能描述:IC CLK SLICER PECL ZDB 28-SSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:1,000 系列:- 类型:时钟/频率合成器，扇出分配 PLL:- 输入:- 输出:- 电路数:- 比率 - 输入:输出:- 差分 - 输入:输出:- 频率 - 最大:- 除法器/乘法器:- 电源电压:- 工作温度:- 安装类型:表面贴装 封装/外壳:56-VFQFN 裸露焊盘 供应商设备封装:56-VFQFP-EP（8x8） 包装:带卷 (TR) 其它名称:844S012AKI-01LFT |
| ICS527R-04T | 功能描述:IC CLK SLICER PECL ZDB 28-SSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS5300V-1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Video DAC with Color Palette (RAMDAC) |
| ICS5300V-2 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Video DAC with Color Palette (RAMDAC) |
发布紧急采购，3分钟左右您将得到回复。