- 您现在的位置：买卖IC网 > PDF目录378608 > IDT7006 (Integrated Device Technology, Inc.) HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM PDF资料下载
参数资料
| 型号： | IDT7006 |
| 厂商： | Integrated Device Technology, Inc. |
| 英文描述： | HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM |
| 中文描述： | 高速16K的× 8双端口静态RAM |
| 文件页数： | 18/20页 |
| 文件大小： | 270K |
| 代理商： | IDT7006 |
6.07
18
IDT7006S/L
HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
system architecture.
An advantage of using semaphores rather than the more
common methods of hardware arbitration is that wait states
are never incurred in either processor. This can prove to be
a major advantage in very high-speed systems.
HOW THE SEMAPHORE FLAGS WORK
The semaphore logic is a set of eight latches which are
independent of the Dual-Port RAM. These latches can be
used to pass a flag, or token, from one port to the other to
indicate that a shared resource is in use. The semaphores
provide a hardware assist for a use assignment method called
“Token Passing Allocation.” In this method, the state of a
semaphore latch is used as a token indicating that shared
resource is in use. If the left processor wants to use this
resource, it requests the token by setting the latch. This
processor then verifies its success in setting the latch by
reading it. If it was successful, it proceeds to assume control
over the shared resource. If it was not successful in setting the
latch, it determines that the right side processor has set the
latch first, has the token and is using the shared resource. The
left processor can then either repeatedly request that
semaphore’s status or remove its request for that semaphore
to perform another task and occasionally attempt again to
gain control of the token via the set and test sequence. Once
the right side has relinquished the token, the left side should
succeed in gaining control.
The semaphore flags are active low. A token is requested
by writing a zero into a semaphore latch and is released when
the same side writes a one to that latch.
The eight semaphore flags reside within the IDT7006 in a
separate memory space from the Dual-Port RAM. This
address space is accessed by placing a low input on the
SEM
pin (which acts as a chip select for the semaphore flags) and
using the other control pins (Address,
OE
, and R/
W
) as they
would be used in accessing a standard Static RAM. Each of
the flags has a unique address which can be accessed by
either side through address pins A0 – A2. When accessing the
semaphores, none of the other address pins has any effect.
When writing to a semaphore, only data pin D
0
is used. If
a low level is written into an unused semaphore location, that
flag will be set to a zero on that side and a one on the other side
(see Table III). That semaphore can now only be modified by
the side showing the zero. When a one is written into the same
location from the same side, the flag will be set to a one for both
sides (unless a semaphore request from the other side is
pending) and then can be written to by both sides. The fact
that the side which is able to write a zero into a semaphore
subsequently locks out writes from the other side is what
makes semaphore flags useful in interprocessor communica-
tions. (A thorough discussing on the use of this feature follows
shortly.) A zero written into the same location from the other
side will be stored in the semaphore request latch for that side
until the semaphore is freed by the first side.
When a semaphore flag is read, its value is spread into all
data bits so that a flag that is a one reads as a one in all data
bits and a flag containing a zero reads as all zeros. The read
value is latched into one side’s output register when that side's
semaphore select (
SEM
) and output enable (
OE
) signals go
active. This serves to disallow the semaphore from changing
state in the middle of a read cycle due to a write cycle from the
other side. Because of this latch, a repeated read of a
semaphore in a test loop must cause either signal (
SEM
or
OE
)
to go inactive or the output will never change.
A sequence WRITE/READ must be used by the sema-
phore in order to guarantee that no system level contention
will occur. A processor requests access to shared resources
by attempting to write a zero into a semaphore location. If the
semaphore is already in use, the semaphore request latch will
contain a zero, yet the semaphore flag will appear as one, a
fact which the processor will verify by the subsequent read
(see Table III). As an example, assume a processor writes a
zero to the left port at a free semaphore location. On a
subsequent read, the processor will verify that it has written
successfully to that location and will assume control over the
resource in question. Meanwhile, if a processor on the right
side attempts to write a zero to the same semaphore flag it will
fail, as will be verified by the fact that a one will be read from
that semaphore on the right side during subsequent read.
Had a sequence of READ/WRITE been used instead, system
contention problems could have occurred during the gap
between the read and write cycles.
It is important to note that a failed semaphore request must
be followed by either repeated reads or by writing a one into
the same location. The reason for this is easily understood by
looking at the simple logic diagram of the semaphore flag in
Figure 4. Two semaphore request latches feed into a sema-
phore flag. Whichever latch is first to present a zero to the
semaphore flag will force its side of the semaphore flag low
and the other side high. This condition will continue until a one
is written to the same semaphore request latch. Should the
other side’s semaphore request latch have been written to a
zero in the meantime, the semaphore flag will flip over to the
other side as soon as a one is written into the first side’s
request latch. The second side’s flag will now stay low until its
semaphore request latch is written to a one. From this it is
easy to understand that, if a semaphore is requested and the
processor which requested it no longer needs the resource,
the entire system can hang up until a one is written into that
semaphore request latch.
The critical case of semaphore timing is when both sides
request a single token by attempting to write a zero into it at
the same time. The semaphore logic is specially designed to
resolve this problem. If simultaneous requests are made, the
logic guarantees that only one side receives the token. If one
side is earlier than the other in making the request, the first
side to make the request will receive the token. If both
requests arrive at the same time, the assignment will be
arbitrarily made to one port or the other.
One caution that should be noted when using semaphores
is that semaphores alone do not guarantee that access to a
resource is secure. As with any powerful programming tech-
nique, if semaphores are misused or misinterpreted, a soft-
ware error can easily happen.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT7014S25JI | HIGH-SPEED 4K x 9DUAL-PORT STATIC RAM |
| IDT7014S25PFI | HIGH-SPEED 4K x 9DUAL-PORT STATIC RAM |
| IDT7014S20JI | HIGH-SPEED 4K x 9DUAL-PORT STATIC RAM |
| IDT7014S20PFI | HIGH-SPEED 4K x 9DUAL-PORT STATIC RAM |
| IDT7014S12JI | HIGH-SPEED 4K x 9DUAL-PORT STATIC RAM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT700620J | 制造商:未知厂家 制造商全称:未知厂家 功能描述:IC-SM-DUAL PORT SRAM |
| IDT7006L | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM |
| IDT7006L15F | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM |
| IDT7006L15FB | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM |
| IDT7006L15G | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM |
发布紧急采购，3分钟左右您将得到回复。