- 您现在的位置：买卖IC网 > PDF目录1924 > IDT82V2044EPFG (IDT, Integrated Device Technology Inc)IC LIU T1/E1 QUAD SHORT 128-TQFP PDF资料下载
参数资料
| 型号： | IDT82V2044EPFG |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 7/73页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1 QUAD SHORT 128-TQFP |
| 标准包装： | 15 |
| 类型： | 线路接口装置（LIU） |
| 规程： | E1 |
| 电源电压： | 3.13 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-TQFP（14x20） |
| 包装： | 托盘 |
| 其它名称： | 82V2044EPFG |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
15
INDUSTRIAL
TEMPERATURE RANGES
QUAD CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
Figure-6 T1 Pulse Template Test Circuit
For J1 applications, the PULS[3:0] (TCF1, 03H...) should be set to
‘0111’. Table-10 lists these values.
3.2.3.2 User-Programmable Arbitrary Waveform
When the PULS[3:0] bits are set to ‘11xx’, user-programmable arbitrary
waveform generator mode can be used in the corresponding channel. This
allows the transmitter performance to be tuned for a wide variety of line con-
dition or special application.
Each pulse shape can extend up to 4 UIs (Unit Interval), addressed by
UI[1:0] bits (TCF3, 05H...) and each UI is divided into 16 sub-phases,
addressed by the SAMP[3:0] bits (TCF3, 05H...). The pulse amplitude of
each phase is represented by a binary byte, within the range from +63 to -
63, stored in WDAT[6:0] bits (TCF4, 06H...) in signed magnitude form. The
most positive number +63 (D) represents the maximum positive amplitude
of the transmit pulse while the mostnegative number -63 (D) represents the
maximum negative amplitude of the transmit pulse. Therefore, up to 64
bytes are used. For each channel, a 64 bytes RAM is available.
There are eight standard templates which are stored in a local ROM.
User can select one of them as reference and make some changes to get
the desired waveform.
User can change the wave shape and the amplitude to get the desired
pulse shape. In order to do this, firstly, users can choose a set of waveform
value from the following eight tables, which is the most similar to the desired
and Table-9 list the sample data and scaling data of each of the eight tem-
plates.Thenmodifythecorrespondingsampledatatogetthedesiredtrans-
mit pulse shape.
Secondly, through the value of SCAL[5:0] bits increased or decreased
by 1, the pulse amplitude can be scaled up or down at the percentage ratio
against the standard pulse amplitude if needed. For different pulse shapes,
the value of SCAL[5:0] bits and the scaling percentage ratio are different.
The following eight tables list these values.
Do the followings step by step, the desired waveform can be pro-
grammed, based on the selected waveform template:
(1).Select the UI by UI[1:0] bits (TCF3, 05H...)
(2).Specify the sample address in the selected UI by SAMP [3:0] bits
(TCF3, 05H...)
(3).Write sample data to WDAT[6:0] bits (TCF4, 06H...). It contains the
data to be stored in the RAM, addressed by the selected UI and the
corresponding sample address.
(4).SettheRWbit(TCF3,05H...)to‘0’toimplementwritingdatatoRAM,
or to ‘1’ to implement read data from RAM
(5).Implement the Read from RAM/Write to RAM by setting the DONE
bit (TCF3, 05H...)
Repeat the above steps until all the sample data are written to or read
from the internal RAM.
(6).Write the scaling data to SCAL[5:0] bits (TCF2, 04H...) to scale the
amplitude of the waveform based on the selected standard pulse
amplitude
WhenmorethanoneUIisusedtocomposethepulsetemplate,theover-
lap of two consecutive pulses could make the pulse amplitude overflow
(exceed the maximum limitation) if the pulse amplitude is not set properly.
This overflow is captured by DAC_OV_IS bit (INTS1, 17H...), and, if
enabled by the DAC_OV_IM bit (INTM1, 12H...), an interrupt will be gen-
erated.
The following tables give all the sample data based on the preset pulse
templates in detail for reference. For preset pulse templates, scaling up/
down against the pulse amplitude is not supported.
1.Table-2 Transmit Waveform Value For E1 75
2.Table-3 Transmit Waveform Value For E1 120
3.Table-4 Transmit Waveform Value For T1 0~133 ft
4.Table-5 Transmit Waveform Value For T1 133~266 ft
5.Table-6 Transmit Waveform Value For T1 266~399 ft
6.Table-7 Transmit Waveform Value For T1 399~533 ft
7.Table-8 Transmit Waveform Value For T1 533~655 ft
8.Table-9 Transmit Waveform Value For J1 0~655 ft
IDT82V2044E
TTIPn
TRINGn
Cable
RLOAD VOUT
Note: RLOAD = 100
± 5%
Table-2 Transmit Waveform Value For E1 75
Sample
UI 1
UI 2
UI 3
UI 4
1
0000000
2
0000000
3
0000000
4
0001100
0000000
5
0110000
0000000
6
0110000
0000000
7
0110000
0000000
8
0110000
0000000
9
0110000
0000000
10
0110000
0000000
11
0110000
0000000
12
0110000
0000000
13
0000000
14
0000000
15
0000000
16
0000000
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0]
results in 3% scaling up/down against the pulse amplitude.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT82V2048DAG | IC LIU T1/E1 8CH SHORT 144-TQFP |
| IDT82V2048EDR | IC LIU T1/E1 8CH SHORT 208-TQFP |
| IDT82V2048LBBG | IC LIU T1/E1 8CH SHORT 160-BGA |
| IDT82V2048SDAG | IC LIU T1/E1 8CH SHORT 144-TQFP |
| IDT82V2051EPPG | IC LIU E1 SGL SHORT HAUL 44-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT82V2044EPFG8 | 功能描述:IC LINE INTERFC UNIT 4CH 128TQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2048 | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:OCTAL T1/E1 SHORT HAUL LINE INTERFACE UNIT |
| IDT82V2048BB | 功能描述:IC LIU T1/E1 8CH SHORT 160-BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2048BBG | 功能描述:IC LIU T1/E1 8CH SHORT 160-BGA RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2048DA | 功能描述:IC LIU T1/E1 8CH SHORT 144-TQFP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。