参数资料
型号: IL300-DEFG
厂商: VISHAY INTERTECHNOLOGY INC
元件分类: 光电元器件
英文描述: SPECIALTY OPTOELECTRONIC DEVICE
文件页数: 7/8页
文件大小: 444K
代理商: IL300-DEFG
Document Number: 83622
www.vishay.com
Revision 17-August-01
7
Table 1 gives the value of R5 given the production K3 bins.
Table 1, R5 selection
The last step in the design is selecting the LED current limiting
resistor (R4). The output of the operational amplier is targeted
to be 50% of the VCC, or 2.5 V. With an LED quiescent current
of 12 mA the typical LED (VF) is 1.3 V. Given this and the oper-
ational output voltage, R4 can be calculated.
The circuit was constructed with an LM201 differential opera-
tional amplier using the resistors selected. The amplier was
compensated with a 100 pF capacitor connected between
pins 1 and 8.
The DC transfer characteristics are shown in Figure 19. The
amplier was designed to have a gain of 0.6 and was mea-
sured to be 0.6036. Greater accuracy can be achieved by
adding a balancing circuit, and potentiometer in the input
divider, or at R5. The circuit shows exceptionally good gain lin-
earity with an RMS error of only 0.0133% over the input voltage
range of 4.0 V–6.0 V in a servo mode; see Figure 20.
Bins
Min.
Max.
3
Typ.
R5
Resistor
K
1%
K
A
0.560
0.623
0.59
50.85
51.1
B
0.623
0.693
0.66
45.45
45.3
C
0.693
0.769
0.73
41.1
41.2
D
0.769
0.855
0.81
37.04
37.4
E
0.855
0.950
0.93
32.26
32.4
F
0.950
1.056
1.00
30.00
30.0
G
1.056
1.175
1.11
27.03
27.0
H
1.175
1.304
1.24
24.19
24.0
I
1.304
1.449
1.37
21.90
22.0
J
1.449
1.610
1.53
19.61
19.4
R4
V
opamp
V
F
I
Fq
--------------------------------
2.5V
1.3V
12mA
------------------------------
100
=
Figure 19. Transfer gain
Figure 20. Linearity error vs. input voltage
The AC characteristics are also quite impressive offering a -
3.0 dB bandwidth of 100 kHz, with a –45
° phase shift at 80 kHz
as shown in Figure 21.
Figure 21. Amplitude and phase power supply control
The same procedure can be used to design isolation ampliers
that accept bipolar signals referenced to ground. These ampli-
ers circuit congurations are shown in Figure 22. In order for the
amplier to respond to a signal that swings above and below
ground, the LED must be prebiased from a separate source by
using a voltage reference source (Vref1). In these designs, R3
can be determined by the following equation.
6.0
5.5
5.0
4.5
4.0
2.25
2.50
2.75
3.00
3.25
3.50
3.75
Vin - Input Voltage - V
Vout
-
Ooutput
Voltage
-
V
Vout = 14.4 mV + 0.6036 x Vin
LM 201 Ta = 25°C
6.0
5.5
5.0
4.5
4.0
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
0.020
0.025
Vin - Input Voltage - V
Linearity
Error
-
%
LM201
dB
PHASE
Phase
Response
-
°
103
104
105
106
2
0
-2
-4
-6
-8
45
0
-45
-90
-135
-180
F - Frequency - Hz
Amplitude
Response
-
dB
R3
V
ref1
I
P1
-------------
V
ref1
K1I
Fq
---------------
=
相关PDF资料
PDF描述
IL300-F-X001 SPECIALTY OPTOELECTRONIC DEVICE
IL300-X001 SPECIALTY OPTOELECTRONIC DEVICE
IL300-X001 SPECIALTY OPTOELECTRONIC DEVICE
IL300-X007T SPECIALTY OPTOELECTRONIC DEVICE
IL300-X009T SPECIALTY OPTOELECTRONIC DEVICE
相关代理商/技术参数
参数描述
IL300-DEFG-X001 功能描述:高线性光耦合器 High Gain Wide Bandwidth Linear RoHS:否 制造商:Avago Technologies 输入类型:AC/DC 最大正向二极管电压:1.95 V 最大反向二极管电压:2.5 V 最大输入二极管电流:25 mA 最大功率耗散:60 mW 最大工作温度:+ 100 C 最小工作温度:- 55 C 封装 / 箱体:DIP-8 Gull Wing 封装:Tube
IL300-DEFG-X006 功能描述:高线性光耦合器 Single Linear, High Gain, Wide Bandwidth RoHS:否 制造商:Avago Technologies 输入类型:AC/DC 最大正向二极管电压:1.95 V 最大反向二极管电压:2.5 V 最大输入二极管电流:25 mA 最大功率耗散:60 mW 最大工作温度:+ 100 C 最小工作温度:- 55 C 封装 / 箱体:DIP-8 Gull Wing 封装:Tube
IL300-DEFG-X007 功能描述:高线性光耦合器 High Gain Wide Bandwidth Linear RoHS:否 制造商:Avago Technologies 输入类型:AC/DC 最大正向二极管电压:1.95 V 最大反向二极管电压:2.5 V 最大输入二极管电流:25 mA 最大功率耗散:60 mW 最大工作温度:+ 100 C 最小工作温度:- 55 C 封装 / 箱体:DIP-8 Gull Wing 封装:Tube
IL300-DEFG-X007 制造商:Vishay Semiconductors 功能描述:; Leaded Process Compatible:Yes; Peak Re
IL300-DEFG-X007T 功能描述:高线性光耦合器 Single Linear, High Gain, Wide Bandwidth RoHS:否 制造商:Avago Technologies 输入类型:AC/DC 最大正向二极管电压:1.95 V 最大反向二极管电压:2.5 V 最大输入二极管电流:25 mA 最大功率耗散:60 mW 最大工作温度:+ 100 C 最小工作温度:- 55 C 封装 / 箱体:DIP-8 Gull Wing 封装:Tube