- 您现在的位置：买卖IC网 > PDF目录13423 > IP1201PBF (International Rectifier)IC REG BUCK SYNC ADJ 30A 198BGA PDF资料下载
参数资料
| 型号： | IP1201PBF |
| 厂商： | International Rectifier |
| 文件页数： | 18/29页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 30A 198BGA |
| 产品变化通告： | (EP) Parts Discontinuation 25/May/2012 |
| 标准包装： | 10 |
| 系列： | iPOWIR™ |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.8 V ~ 3.3 V |
| 输入电压： | 3.14 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 400kHz |
| 电流 - 输出： | 30A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 198-BGA（159 凸块） |
| 包装： | 散装 |
| 供应商设备封装： | BGA（15.5x9.25） |
| 配用： | IRDCIP1201-A-ND - BUCK CONV REF DESIGN KIT IP1201 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
iP1201PbF
I RMS = 6 x SQRT (0.75(1 - 0.75)) = 2.6A
For better efficiency and low input ripple, select low
ESR ceramic capacitors. The amount of the capaci-
tors is determined based on the r.m.s. rating. In the
above example, a total of 3 x 100 μ F, 3.5A capacitors
will be required to support the input r.m.s. current
(see the parts list in the reference design section of
this datasheet).
The 18 0° out of phase operation of the iP1201PbF pro-
vides reduced voltage ripple at the input of the device.
This reduction in ripple requires less input bypass ca-
pacitance. Therefore the input bypass capacitor se-
lection criteria based on equation (3) provides a worst
case solution for the selected operating conditions.
Output Capacitor C O Selection
Selection of the output capacitors depends on two
factors:
a. Low effective ESR for ripple and load transient
requirements
To support the load transients and to stay within a
specified voltage dip ? V due to the transients, e.s.r.
selection should satisfy equation (4):
properly compensate the control loop for low output
capacitor e.s.r. values.
When selecting output capacitors, it is important to
consider the overshoot performance of the power
supply. If the amount of capacitance is not adequate,
then, when unloading the output, the magnitude of
the overshoot due to stored inductor energy, and
depending on the speed of the response of the con-
trol loop, can exceed the overvoltage trip threshold
of the iP1201PbF and can cause undesirable shutdown
of the output. The magnitude of the overshoot should
be kept below 1.125V OUT . To prevent the overshoot
from tripping the output a delay can be added by
installing capacitor C26 as shown in Fig.19.
In paralleled single output configuration, due to 180 °
phase shift, the peak to peak output voltage ripple
will be reduced because of doubling of the ripple
frequency. Also, the resulting ripple current in the
output capacitors will be smaller than the ripple cur-
rent of each channel. There is some cancellation
effect of these current, the magnitude of which de-
pends on the duty cycle.
b. Stability
R esr ≤ ? V / I Loadmax
Where,
I Loadmax is the maximum load current.
(4)
The value of the output capacitor e.s.r. zero frequency
f esr plays a major role in determining stability. f esr is
calculated by the expression in equation (6).
f esr = 1 / (2 π x R esr x C O ) (6)
If output voltage ripple is required to be maintained
at specified levels then, the expression in equation
(5) should be used to select the output capacitors.
Details on how to consider this parameter to design
for stability will be outlined in the control loop com-
pensation section of this datasheet.
R esr ≤ V p-p / I ripple
(5)
Inductor L O Selection
Where,
V p-p is the single phase peak to peak output voltage
ripple.
I ripple is the inductor current peak-to peak ripple.
If the inductor current ripple I ripple is 30% of I OUT1, the
40mV peak to peak output voltage ripple require-
ment will be met if the total e.s.r. of the output capaci-
tors is less than 11mohms. This will require 3 x
470 μ F POSCAP capacitors (See the parts list in the
reference design section of this datasheet). Addi-
tional ceramic capacitors can be added in parallel
to further reduce the e.s.r. Care should be given to
18
Inductor selection is based on trade-offs between
size and efficiency. Low inductor values result in
smaller sizes, but can cause large ripple currents
and lower efficiency. Low inductor values also ben-
efit the transient performance.
The inductor L o is selected according to equation (7):
L O = V out x (1 - D) / (f sw x I ripple ) (7)
For output 1 of the above example, and for I ripple of
30% of I OUT1 , L O1 is calculated to be 1.1 μ H.
The core must be selected according to the peak of
maximum output current.
A similar calculation can be applied to find an induc-
www.irf.com
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8214BCSE+T | IC MONITOR VOLT MPU 16-SOIC |
| IP1202PBF | IC REG BUCK SYNC ADJ 30A 198BG |
| MAX8213BCSE+T | IC MONITOR VOLT MPU 16-SOIC |
| RBM40DTMD-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| GCM36DTBD-S664 | CONN EDGECARD 72POS R/A .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IP1201TR | 功能描述:开关变换器、稳压器与控制器 DUAL OUTPUT 2-Phase 3.14 to 5V 400kHz RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IP1201TRPBF | 功能描述:开关变换器、稳压器与控制器 DUAL OUTPUT 2-Phase 3.14 to 5V 400kHz RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IP1202 | 功能描述:开关变换器、稳压器与控制器 DUAL OUTPUT 2-Phase 5.5V to 13.2V 15A RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IP1202PBF | 功能描述:开关变换器、稳压器与控制器 DUAL OUTPUT 2-Phase 5.5V to 13.2V 15A RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IP1202PBF-EL | 制造商:International Rectifier 功能描述: |
发布紧急采购，3分钟左右您将得到回复。