- 您现在的位置：买卖IC网 > Datasheet目录690 > IS-C1603 (NKK Switches)CONTROL FOR 36X24 LCD PB/DISPLAY Datasheet资料下载
参数资料
| 型号： | IS-C1603 |
| 厂商： | NKK Switches |
| 文件页数： | 48/52页 |
| 文件大小： | 0K |
| 描述： | CONTROL FOR 36X24 LCD PB/DISPLAY |
| 产品培训模块： | Smart Switch Overview |
| 视频文件： | OLED Pushbutton in Action |
| RoHS指令信息： | AT, IS Series, Cert of Compliance |
| 标准包装： | 1 |
| 附件类型： | 控制器 |
| 适用于相关产品： | SmartSwitch? 开关 |
| 产品目录页面： | 2526 (CN2011-ZH PDF) |
| 配用： | IS01BCEF-ND - SMARTDISPLAY SUPER YEL/GRN LED IS01BCE-ND - SMARTDISPLAY SUPER YELLOW LED IS15SBFP4B-ND - SMARTSWITCH COMPACT WHITE LED IS15SBCP4EF-ND - SMARTSWITCH COMPACT YEL/GRN LED IS15SACP4CF-ND - SMARTSWITCH COMPACT RED/GRN LED IS15ABFP4B-ND - SMARTSWITCH STD BLK W/WHITE LED IS15ABDP4B-ND - SMARTSWITCH STD BLU W/WHITE LED IS15ABDP4EG-ND - SMARTSWITCH STD YELLOW/BLUE LED IS15ABDP4E-ND - SMARTSWITCH STD BLUE W/YEL LED IS15ABCP4EF-ND - SMARTSWITCH STD YEL/GRN LED 更多... |
| 其它名称： | 360-2427 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页
IS-C1603 Intelligent Controller User
Manual
7850 East Gelding Drive ? Scottsdale, AZ 85260-3420
8. Programming the Firmware
The controller firmware can be programmed via the RS232 connection.
The Dallas semiconductor MTK software can be downloaded from the site below.
http://www.maxim-ic.com/products/microcontrollers/software/index.cfm#development
After you install the MTK software follow the following instructions to program the microcontroller:
1. Disconnect the switches from the controller at JP2.
2. Install a jumper on JPR connector (top right side of the board). This will put the microcontroller into
programming mode.
3. Run MTK software.
4. Select device DS89C450.
5. Under menu item “Options” select the “Configure Serial Port” and select relevant port and 19200 baud rate.
6. Under menu item “Target” select “Open COM X at 19200 baud”.
7. Plug in or power up the IS-C1603 controller.
8. Under menu item “Target” select “Connect to Loader”.
9. The microcontroller will respond with a version number and copyright notice in blue.
10. Under menu item “File” select “Load Flash”.
11. Specify the HEX file provided by NKK Switches (e.g. C1603V14.HEX)
12. Once loaded the display shall say “Load Complete”
Note: The switches should not be connected while programming the controller since they are not being
refreshed during programming.
9. Firmware Issues
The problems found in the most current version are listed below and will be resolved in the following version.
Version 1.3
No firmware issues at this time.
Version 1.4
In version 1.4 the LCD refresh rate has been increased to have better contrast. All the timers run faster
than stated in the user manual.
No firmware issues at this time.
IS-C1603 Intelligent Controller User Manual D.doc
Toll Free 1.877.2BUYNKK (877.228.9655) ? Phone 480.991.0942 ? Fax 480.998.1435
www.nkkswitches.com ? Email engineering@nkkswitches.com
Page 48 of 52
0110
相关PDF资料 |
PDF描述 |
|---|---|
| IS-L0205-C | LOGIC BOARD FOR 36X24 LCD |
| IS-L02H2-C | BOARD LOGIC 2 HI RES SW SOCKETS |
| IS-L02L1-C | BOARD LOGIC 2 OLED SW SOCKETS |
| IS15AACP4CF | SMARTSWITCH STD YEL RED/GRN LED |
| IS15ABCP4EF | SMARTSWITCH STD YEL/GRN LED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS-C1603-CONTROLLER | 功能描述:CTLR FOR 16 STD SMART SWITCHES RoHS:是 类别:开关 >> 配件 系列:- 标准包装:100 系列:- 其它名称:886.0007886.0007-ND |
| IS-C1603H | 功能描述:交换机开发工具 RoHS:否 制造商:NKK Switches 工具用于评估:Smart Switch - Compact RGB 工作电压: 最大工作温度: |
| ISC1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
| ISC-1812 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Surface Mount, Molded, Shielded Inductors |
发布紧急采购，3分钟左右您将得到回复。