- 您现在的位置：买卖IC网 > PDF目录384512 > IS42S16400B-7T (Electronic Theatre Controls, Inc.) 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM PDF资料下载
参数资料
| 型号： | IS42S16400B-7T |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM |
| 中文描述： | 1梅格位× 16位× 4银行（64兆位）同步动态RAM |
| 文件页数： | 18/55页 |
| 文件大小： | 472K |
| 代理商： | IS42S16400B-7T |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
IS42S16400B
ISSI
18
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. D
02/10/05
DON'T CARE
UNDEFINED
CLK
COMMAND
DQ
READ
NOP
NOP
NOP
CAS Latency - 3
t
AC
t
OH
D
OUT
T0
T1
T2
T3
T4
t
LZ
CLK
COMMAND
DQ
READ
NOP
NOP
CAS Latency - 2
t
AC
t
OH
D
OUT
T0
T1
T2
T3
t
LZ
CAS Latency
CAS Latency
The CAS latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the first
piece of output data. The latency can be set to two or three clocks.
If a READ command is registered at clock edge n, and the
latency is m clocks, the data will be available by clock
edge n + m. The DQs will start driving as a result of the
clock edge one cycle earlier (n + m 1), and provided that
the relevant access times are met, the data will be valid
by clock edge n + m. For example, assuming that the
clock cycle time is such that all relevant access times are
met, if a READ command is registered at T0 and the
latency is programmed to two clocks, the DQs will start
driving after T1 and the data will be valid by T2, as shown
in CAS Latency diagrams. The
Allowable Operating
Frequency
table indicates the operating frequencies at
which each CAS latency setting can be used.
Reserved states should not be used as unknown operation
or incompatibility with future versions may result.
CAS Latency
Allowable Operating Frequency (MHz)
Speed
CAS Latency = 2
CAS Latency = 3
6
100
166
7
100
143
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used
because unknown operation or incompatibility with future
versions may result.
相关PDF资料 |
PDF描述 |
|---|---|
| IS42S16400B-7TL | 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM |
| IS4N45 | LOW INPUT CURRENT DARLINGTON OUTPUT OPTICALLY COUPLED ISOLATOR |
| IS4N46 | LOW INPUT CURRENT DARLINGTON OUTPUT OPTICALLY COUPLED ISOLATOR |
| IS6003 | OPTICALLY COUPLED BILATERAL SWITCH NON-ZERO CROSSING TRIAC |
| IS6005 | OPTICALLY COUPLED BILATERAL SWITCH NON-ZERO CROSSING TRIAC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS42S16400B-7TI | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM |
| IS42S16400B-7TL | 制造商:Integrated Silicon Solution Inc 功能描述:64M, 3.3V SDRAM 4M X 16 143MHZ TSOP |
| IS42S16400B-7TLI | 制造商:Integrated Silicon Solution Inc 功能描述: |
| IS42S16400B-7TLI-TR | 制造商:Integrated Silicon Solution Inc 功能描述: |
| IS42S16400B-7TL-TR | 制造商:Integrated Silicon Solution Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。