参数资料
型号: IS42S16400B-7TL
厂商: Electronic Theatre Controls, Inc.
英文描述: 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM
中文描述: 1梅格位× 16位× 4银行(64兆位)同步动态RAM
文件页数: 13/55页
文件大小: 472K
代理商: IS42S16400B-7TL
IS42S16400B
ISSI
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. D
02/10/05
13
AC ELECTRICAL CHARACTERISTICS
(1,2,3)
-6
-7
Symbol
Parameter
Min.
Max.
Min.
Max.
Units
t
CK3
t
CK2
Clock Cycle Time
CAS
Latency = 3
CAS
Latency = 2
6
7
ns
ns
10
10
t
AC3
t
AC2
Access Time From CLK
(4)
CAS
Latency = 3
CAS
Latency = 2
6
9
6
9
ns
ns
t
CHI
CLK HIGH Level Width
2
2.5
ns
t
CL
CLK LOW Level Width
2
2.5
ns
t
OH3
t
OH2
Output Data Hold Time
CAS
Latency = 3
CAS
Latency = 2
2.5
2.5
2.5
2.5
ns
ns
t
LZ
Output LOW Impedance Time
0
0
ns
t
HZ3
t
HZ2
Output HIGH Impedance Time
(5)
CAS
Latency = 3
CAS
Latency = 2
6
9
6
9
ns
ns
t
DS
Input Data Setup Time
1.5
1.5
ns
t
DH
Input Data Hold Time
0.8
0.8
ns
t
AS
Address Setup Time
1.5
1.5
ns
t
AH
Address Hold Time
0.8
0.8
ns
t
CKS
CKE Setup Time
1.5
1.5
ns
t
CKH
CKE Hold Time
0.8
0.8
ns
t
CKA
CKE to CLK Recovery Delay Time
1CLK+3
1CLK+3
ns
t
CS
Command Setup Time (
CS
,
RAS
,
CAS
,
WE
, DQM)
1.5
2.0
ns
t
CH
Command Hold Time (
CS
,
RAS
,
CAS
,
WE
, DQM)
0.8
1
ns
t
RC
Command Period (REF to REF / ACT to ACT)
60
63
ns
t
RAS
Command Period (ACT to PRE)
35
50,000
37
50,000
ns
t
RP
Command Period (PRE to ACT)
16
16
ns
t
RCD
Active Command To Read / Write Command Delay Time
16
16
ns
t
RRD
Command Period (ACT [0] to ACT[1])
14
14
ns
t
DPL3
Input Data To Precharge
Command Delay time
CAS
Latency = 3
2CLK
2CLK
ns
t
DPL2
CAS
Latency = 2
2CLK
2CLK
ns
t
DAL3
Input Data To Active / Refresh
Command Delay time (During Auto-Precharge)
CAS
Latency = 3
2CLK+t
RP
2CLK+t
RP
ns
t
DAL2
CAS
Latency = 2
2CLK+t
RP
2CLK+t
RP
ns
t
T
Transition Time
1
10
1
10
ns
t
REF
Notes:
1. When power is first applied, memory operation should be started 100 μs after V
DD
and V
DDQ
reach their stipulated voltages.
Also note that the power-on sequence must be executed before starting memory operation.
2. Measured with t
T
= 1 ns.
3. The reference level is 1.4 V when measuring input signal timing. Rise and fall times are measured between V
IH
(min.) and V
IL
(max.).
4. Access time is measured at 1.4V with the load shown in the figure below.
5. The time t
HZ
(max.) is defined as the time required for the output voltage to transition by ± 200 mV from V
OH
(min.) or V
OL
(max.)
when the output is in the high impedance state.
Refresh Cycle Time (4096)
64
64
ms
相关PDF资料
PDF描述
IS4N45 LOW INPUT CURRENT DARLINGTON OUTPUT OPTICALLY COUPLED ISOLATOR
IS4N46 LOW INPUT CURRENT DARLINGTON OUTPUT OPTICALLY COUPLED ISOLATOR
IS6003 OPTICALLY COUPLED BILATERAL SWITCH NON-ZERO CROSSING TRIAC
IS6005 OPTICALLY COUPLED BILATERAL SWITCH NON-ZERO CROSSING TRIAC
IS6010 OPTICALLY COUPLED BILATERAL SWITCH NON-ZERO CROSSING TRIAC
相关代理商/技术参数
参数描述
IS42S16400B-7TLI 制造商:Integrated Silicon Solution Inc 功能描述:
IS42S16400B-7TLI-TR 制造商:Integrated Silicon Solution Inc 功能描述:
IS42S16400B-7TL-TR 制造商:Integrated Silicon Solution Inc 功能描述:
IS42S16400C1 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM
IS42S16400C1-6T 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:1 Meg Bits x 16 Bits x 4 Banks (64-MBIT) SYNCHRONOUS DYNAMIC RAM