- 您现在的位置：买卖IC网 > PDF目录67722 > IS80C32-12PL (INTEGRATED SILICON SOLUTION INC) 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44 PDF资料下载
参数资料
| 型号： | IS80C32-12PL |
| 厂商： | INTEGRATED SILICON SOLUTION INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44 |
| 封装： | PLASTIC, LCC-44 |
| 文件页数： | 29/48页 |
| 文件大小： | 379K |
| 代理商： | IS80C32-12PL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
IS80C52
IS80C32
Integrated Silicon Solution, Inc. — 1-800-379-4774
35
MC004-1D
11/19/98
ISSI
Power-Saving Modes of Operation
The IS80C52/32 has two power-reducing modes. Idle and
Power-down. The input through which backup power is
supplied during these operations is Vcc. Figure 23 shows
the internal circuitry which implements these features. In
the Idle mode (IDL = 1), the oscillator continues to run and
the Interrupt, Serial Port, and Timer blocks continue to be
clocked, but the clock signal is gated off to the CPU. In
Power-down (PD = 1), the oscillator is frozen. The Idle and
Power-down modes are activated by setting bits in Special
Function Register PCON.
Idle Mode
An instruction that sets PCON.0 is the last instruction
executed before the Idle mode begins. In the Idle mode,
the internal clock signal is gated off to the CPU, but not to
the Interrupt, Timer, and Serial Port functions. The CPU
status is preserved in its entirety: the Stack Pointer,
Program Counter, Program Status Word, Accumulator,
and all other registers maintain their data during Idle. The
port pins hold the logical states they had at the time Idle
was activated. ALE and PSEN hold at logic high levels.
There are two ways to terminate the Idle. Activation of any
enabled interrupt will cause PCON.0 to be cleared by
hardware, terminating the Idle mode. The interrupt will be
serviced, and following RETI the next instruction to be
executed will be the one following the instruction that put
the device into Idle.
The flag bits GF0 and GF1 can be used to indicate whether
an interrupt occurred during normal operation or during an
Idle. For example, an instruction that activates Idle can
also set one or both flag bits. When Idle is terminated by
an interrupt, the interrupt service routine can examine the
flag bits.
The other way of terminating the Idle mode is with a
hardware reset. Since the clock oscillator is still running,
the hardware reset must be held active for only two
machine cycles (24 oscillator periods) to complete the
reset.
The signal at the RST pin clears the IDL bit directly and
asynchronously. At this time, the CPU resumes program
execution from where it left off; that is, at the instruction
following the one that invoked the Idle Mode. As shown in
Figure 22, two or three machine cycles of program
execution may take place before the internal reset algorithm
takes control. On-chip hardware inhibits access to the
internal RAM during his time, but access to the port pins
is not inhibited. To eliminate the possibility of unexpected
outputs at the port pins, the instruction following the one
that invokes Idle should not write to a port pin or to external
data RAM.
Power-down Mode
An instruction that sets PCON.1 is the last instruction
executed before Power-down mode begins. In the Power-
down mode, the on-chip oscillator stops. With the clock
frozen, all functions are stopped, but the on-chip RAM and
Special function Registers are held. The port pins output
the values held by their respective SFRs. ALE and
PSEN
output lows.
In the Power-down mode of operation, Vcc can be reduced
to as low as 2V. However, Vcc must not be reduced before
the Power-down mode is invoked, and Vcc must be restored
to its normal operating level before the Power-down mode
is terminated. The reset that terminates Power-down also
frees the oscillator. The reset should not be activated before
Vcc is restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and
stabilize (normally less than 10 msec).
The only exit from power-down is a hardware reset. Reset
redefines all the SFRs but does not change the on-chip
RAM.
OSC
CLOCK
GEN
PD
XTAL 2
XTAL 1
IDL
CPU
INTERRUPT,
SERIAL PORT,
TIMER BLOCKS
Figure 23. Idle and Power-Down Hardware
相关PDF资料 |
PDF描述 |
|---|---|
| IS80C32-40PLI | 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44 |
| IS80C52PL | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQCC44 |
| IS80C732-C | 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44 |
| IS80C732-M | 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44 |
| IS82C55A-596 | 24 I/O, PIA-GENERAL PURPOSE, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS80C32-12PLI | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP LOW VOLTAGE 8-BIT MICROCONTROLLER |
| IS80C32-12PQ | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP LOW VOLTAGE 8-BIT MICROCONTROLLER |
| IS80C32-12PQI | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP LOW VOLTAGE 8-BIT MICROCONTROLLER |
| IS80C32-12R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| IS80C32-12W | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP LOW VOLTAGE 8-BIT MICROCONTROLLER |
发布紧急采购，3分钟左右您将得到回复。