参数资料
型号: IS80C52CXXX-12:D
厂商: TEMIC SEMICONDUCTORS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44
文件页数: 29/134页
文件大小: 3805K
124
8011Q–AVR–02/2013
ATmega164P/324P/644P
The timing diagram for the CTC mode is shown in Figure 13-6. The counter value (TCNTn)
increases until a compare match occurs with either OCRnA or ICRn, and then counter (TCNTn)
is cleared.
Figure 13-6. CTC Mode, Timing Diagram
An interrupt can be generated at each time the counter value reaches the TOP value by either
using the OCFnA or ICFn Flag according to the register used to define the TOP value. If the
interrupt is enabled, the interrupt handler routine can be used for updating the TOP value. How-
ever, changing the TOP to a value close to BOTTOM when the counter is running with none or a
low prescaler value must be done with care since the CTC mode does not have the double buff-
ering feature. If the new value written to OCRnA or ICRn is lower than the current value of
TCNTn, the counter will miss the compare match. The counter will then have to count to its max-
imum value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur.
In many cases this feature is not desirable. An alternative will then be to use the fast PWM mode
using OCRnA for defining TOP (WGMn3:0 = 15) since the OCRnA then will be double buffered.
For generating a waveform output in CTC mode, the OCnA output can be set to toggle its logical
level on each compare match by setting the Compare Output mode bits to toggle mode
(COMnA1:0 = 1). The OCnA value will not be visible on the port pin unless the data direction for
the pin is set to output (DDR_OCnA = 1). The waveform generated will have a maximum fre-
quency of f
OCnA = fclk_I/O/2 when OCRnA is set to zero (0x0000). The waveform frequency is
defined by the following equation:
The N variable represents the prescaler factor (1, 8, 64, 256, or 1024).
As for the Normal mode of operation, the TOVn Flag is set in the same timer clock cycle that the
counter counts from MAX to 0x0000.
13.9.3
Fast PWM Mode
The fast Pulse Width Modulation or fast PWM mode (WGMn3:0 = 5, 6, 7, 14, or 15) provides a
high frequency PWM waveform generation option. The fast PWM differs from the other PWM
options by its single-slope operation. The counter counts from BOTTOM to TOP then restarts
from BOTTOM. In non-inverting Compare Output mode, the Output Compare (OCnx) is cleared
on the compare match between TCNTn and OCRnx, and set at BOTTOM. In inverting Compare
Output mode output is set on compare match and cleared at BOTTOM. Due to the single-slope
operation, the operating frequency of the fast PWM mode can be twice as high as the phase cor-
TCNTn
OCnA
(Toggle)
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
1
4
Period
2
3
(COMnA1:0 = 1)
f
OCnA
f
clk_I/O
2 N
1
OCRnA
+
---------------------------------------------------
=
相关PDF资料
PDF描述
IS80C52CXXX-20:R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44
IS80C52CXXX-25:D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
IS80C52CXXX-25:R 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
IS80C52CXXX-25SHXXX:D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44
IS80C52CXXX-30SHXXX:RD 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44
相关代理商/技术参数
参数描述
IS80C86 制造商:Rochester Electronics LLC 功能描述:- Bulk
IS80C86-2 制造商:Rochester Electronics LLC 功能描述:- Bulk
IS80C86-2R2490 制造商:Rochester Electronics LLC 功能描述:- Bulk
IS80C88 制造商:Rochester Electronics LLC 功能描述:- Bulk
IS80C88-2 制造商:Rochester Electronics LLC 功能描述:- Bulk