- 您现在的位置：买卖IC网 > PDF目录384512 > IS80C88-2 (INTERSIL CORP) CMOS 8/16-Bit Microprocessor PDF资料下载
参数资料
| 型号： | IS80C88-2 |
| 厂商： | INTERSIL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | CMOS 8/16-Bit Microprocessor |
| 中文描述： | 16-BIT, 8 MHz, MICROPROCESSOR, PQCC44 |
| 封装： | PLASTIC, LCC-44 |
| 文件页数： | 8/32页 |
| 文件大小： | 246K |
| 代理商： | IS80C88-2 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
3-8
The BIU will automatically execute two fetch or write cycles
for 16-bit operands.
Certain locations in memory are reserved for specific CPU
operations. (See Figure 2). Locations from addresses
FFFF0H through FFFFFH are reserved for operations
including a jump to initial system initialization routine. Follow-
ing RESET, the CPU will always begin execution at location
FFFF0H where the jump must be located. Locations 00000H
through 003FFH are reserved for interrupt operations. Each
of the 256 possible interrupt service routines is accessed
through its own pair of 16-bit pointers - segment address
pointer and offset address pointer. The first pointer, used as
the offset address, is loaded into the IP, and the second
pointer, which designates the base address, is loaded into
the CS. At this point program control is transferred to the
interrupt routine. The pointer elements are assumed to have
been stored at their respective places in reserved memory
prior to the occurrence of interrupts.
Minimum and Maximum Modes
The requirements for supporting minimum and maximum
80C88 systems are sufficiently different that they cannot be
done efficiently with 40 uniquely defined pins. Consequently,
the 80C88 is equipped with a strap pin (MN/MX) which
defines the system configuration. The definition of a certain
subset of the pins changes, dependent on the condition of
the strap pin. When the MN/MX pin is strapped to GND, the
80C88 defines pins 24 through 31 and 34 in maximum
mode. When the MN/MX pins is strapped to V
CC
, the 80C88
generates bus control signals itself on pins 24 through 31
and 34.
The minimum mode 80C88 can be used with either a
muliplexed or demultiplexed bus. This architecture provides
the 80C88 processing power in a highly integrated form.
The demultiplexed mode requires one latch (for 64K addres-
sability) or two latches (for a full megabyte of addressing).
An 82C86 or 82C87 transceiver can also be used if data bus
buffering is required. (See Figure 3). The 80C88 provides
DEN and DT/R to control the transceiver, and ALE to latch
the addresses. This configuration of the minimum mode pro-
vides the standard demultiplexed bus structure with heavy
bus buffering and relaxed bus timing requirements.
The maximum mode employs the 82C88 bus controller (See
Figure 4). The 82C88 decode status lines S0, S1 and S2,
and provides the system with all bus control signals. Moving
the bus control to the 82C88 provides better source and sink
current capability to the control lines, and frees the 80C88
pins for extended large system features. Hardware lock,
queue status, and two request/grant interfaces are provided
by the 80C88 in maximum mode. These features allow
coprocessors in local bus and remote bus configurations.
TYPE 255 POINTER
(AVAILABLE)
RESET BOOTSTRAP
PROGRAM JUMP
TYPE 33 POINTER
(AVAILABLE)
TYPE 32 POINTER
(AVAILABLE)
TYPE 31 POINTER
(AVAILABLE)
TYPE 5 POINTER
(RESERVED)
TYPE 4 POINTER
OVERFLOW
TYPE 3 POINTER
1 BYTE INT INSTRUCTION
TYPE 2 POINTER
NON MASKABLE
TYPE 1 POINTER
SINGLE STEP
TYPE 0 POINTER
DIVIDE ERROR
16-BITS
CS BASE ADDRESS
IP OFFSET
014H
010H
00CH
008H
004H
000H
07FH
080H
084H
FFFF0H
FFFFFH
3FFH
3FCH
AVAILABLE
INTERRUPT
POINTERS
(224)
DEDICATED
INTERRUPT
POINTERS
(5)
RESERVED
INTERRUPT
POINTERS
(27)
FIGURE 15. RESERVED MEMORY LOCATIONS
80C88
相关PDF资料 |
PDF描述 |
|---|---|
| IS82C50A-5 | CMOS Asynchronous Communications Element |
| IS82C52 | CMOS Serial Controller Interface |
| IS82C54 | CMOS Programmable Interval Timer |
| IS82C54-10 | CMOS Programmable Interval Timer |
| IS82C54-12 | CMOS Programmable Interval Timer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS80D | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NC |
| IS80DK | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NC |
| IS80K | 制造商:IDEC CORPORATION 功能描述:SENS.IND. 2W/F 24-230VAC NC |
| IS80LV31 | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP LOW VOLTAGE 8-BIT MICROCONTROLLER |
| IS80LV31-24PL | 制造商:ISSI 制造商全称:Integrated Silicon Solution, Inc 功能描述:CMOS SINGLE CHIP LOW VOLTAGE 8-BIT MICROCONTROLLER |
发布紧急采购，3分钟左右您将得到回复。