- 您现在的位置：买卖IC网 > PDF目录11818 > IS82C50A-5 (Intersil)IC PERIPH UART/BRG 10MHZ 44-PLCC PDF资料下载
参数资料
| 型号： | IS82C50A-5 |
| 厂商： | Intersil |
| 文件页数： | 8/25页 |
| 文件大小： | 0K |
| 描述： | IC PERIPH UART/BRG 10MHZ 44-PLCC |
| 标准包装： | 26 |
| 特点： | 单芯片 UART/BRG |
| 通道数： | 1，UART |
| 规程： | RS232C |
| 电源电压： | 4.5 V ~ 5.5 V |
| 带并行端口： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 管件 |
16
FN2958.5
August 24, 2006
82C50A
Programming
The 82C50A is programmed by the control registers LCR,
lER, DLL and DLM, and MCR. These control words define
the character length, number of stop bits, parity, baud rate,
and modem interface.
While the control registers can be written in any order, the
lER should be written to last because it controls the interrupt
enables. Once the 82C50A is programmed and operational,
these registers can be updated any time the 82C50A is not
transmitting or receiving data.
The control signals required to access 82C50A internal
registers are shown below.
Software Reset
A software reset of the 82C50A is a useful method for
returning to a completely known state without a system
reset. Such a reset consists of writing to the LCR, Divisor
Latches, and MCR registers. The LSR and RBR registers
should be read prior to enabling interrupts in order to clear
out any residual data or status bits which may be invalid for
subsequent operation.
Crystal Operation
The 82C50A crystal oscillator circuitry is designed to operate
with a fundamental mode, parallel resonant crystal. Table 8
shows the required crystal parameters and crystal circuit
configuration, respectively.
When using an external clock source, the XTAL1 input is
driven and the XTAL2 output is left open. Power
consumption when using an external clock is typically 50%
of that required when using a crystal. This is due to the
sinusoidal nature of the drive circuitry when using a crystal.
The maximum frequency of the 82C50A is 10MHz with an
external clock or a crystal attached to XTAL1 and XTAL2.
Using the external clock or crystal, and a divide by one
divisor, the maximum BAUDOUT is 10MHz, and the
maximum data rate is 625Kbps.
TABLE 8. TYPICAL CRYSTAL OSCILLATOR CIRCUIT
PARAMETER
Frequency
1.0 to 10MHz
Type of Operation
Parallel Resonant, Fundamental
Mode
Load Capacitance (CL)
20 or 32pF (Typ)
RSERIES (Max)
100
Ω (f = 10MHz, CL = 32pF)
200
Ω (f = 10MHz, CL = 20pF)
FIGURE 2. TYPICAL CRYSTAL OSCILLATOR CIRCUIT
CL
XTAL
XTAL1
XTAL2
TO
BAUD RATE
GENERATOR
LOGIC
PIN 17
PIN 16
RS
CL
82C50A
相关PDF资料 |
PDF描述 |
|---|---|
| IS82C50A-5Z | IC PERIPH UART/BRG 10MHZ 44-PLCC |
| ATMEGA329-16MUR | MCU AVR 32K FLASH 16MHZ 64QFN |
| CS82C50A-5Z96 | IC ASYNC COMM ELEMNT UART 44PLCC |
| CS82C50A-5Z | IC COMMUNICATION ELEMENT 44-PLCC |
| CP82C52Z | IC UART/BRG 5V 16MHZ 28-PDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS82C50A-5Z | 功能描述:UART 接口集成电路 W/ANNEAL PERIPH UART /BRG 5V 10MHZ RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| IS82C52 | 功能描述:UART 接口集成电路 PERIPH UART/BRG 5V 16MHZ 28PLCC IND RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| IS82C52/TR100/BAE | 制造商:Intersil Corporation 功能描述:PERIPH UART/BRG 5V 16MHZ 28PLCC IND - Tape and Reel |
| IS82C5296 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C52R2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。