- 您现在的位置：买卖IC网 > PDF目录384512 > IS82C52 (INTERSIL CORP) CMOS Serial Controller Interface PDF资料下载
参数资料
| 型号： | IS82C52 |
| 厂商： | INTERSIL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | CMOS Serial Controller Interface |
| 中文描述： | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC28 |
| 封装： | PLASTIC, LCC-28 |
| 文件页数： | 4/19页 |
| 文件大小： | 255K |
| 代理商： | IS82C52 |
5-4
Reset
During and after power-up, the 82C52 Reset Input (RST)
must be held high for at least two IX clock cycles in order to
initialize and drive the 82C52 circuits to an idle mode until
proper programming can be done. A high on RST causes
the following events to occur
Resets the internal Baud Rate Generator (BRG) circuit
clock counters and bit counters. The Baud Rate Select
Register (BRSR) is not affected (except for bit 7 which is
reset to 0).
Clears the UART Status Register (USR) except for
Transmission Complete (TC) and Transmit Buffer Register
Empty (TBRE) which are set. The Modem Control
Register (MCR) is also cleared. All of the discrete lines,
memory elements and miscellaneous logic associated
with these register bits are also cleared or turned off. Note
that the UART Control Register (UCR) is not affected.
Following removal of the reset condition (RST = low), the
82C52 remains in the idle mode until programmed to its
desired system configuration.
Programming The 82C52
The complete functional definition of the 82C52 is
programmed by the systems software. A set of control words
(UCR, BRSR and MCR) must be sent out by the CPU to
initialize the 82C52 to support the desired communication
format. These control words will program the character
length, number of stop bits, even/odd/no parity, baud rate,
etc. Once programmed, the 82C52 is ready to perform its
communication functions.
The control registers can be written to in any order. However,
the MCR should be written to last because it controls the
interrupt enables, modem control outputs and the receiver
enable bit. Once the 82C52 is programmed and operational,
these registers can be updated any time the 82C52 is not
immediately transmitting or receiving data.
Table 1. Shows the control signals required to access 82C52
internal registers.
UART Control Register (UCR)
The UCR is a write only register which configures the UART
transmitter and receiver circuits. Data bits D7 and D6 are not
used but should always be set to a logic zero (0) in order to
insure software compatibility with future product upgrades.
During the Echo Mode, the transmitter always repeats the
received word and parity, even when the UCR is
programmed with different or no parity. See Figure 1.
TABLE 1.
CS0
A1
A0
WR
RD
OPERATION
0
0
0
0
1
Data Bus
→
Transmitter Buffer
Register (TBR)
0
0
0
1
0
Receiver Buffer Register
(RBR)
→
Data Bus
0
0
1
0
1
Data Bus
→
UART Control
Register (UCR)
0
0
1
1
0
UART Status Register
(USR)
→
Data Bus
0
1
0
0
1
Data Bus
→
Modem Control
Register (MCR)
0
1
0
1
0
MCR
→
Data Bus
0
1
1
0
1
Data Bus
→
Bit Rate Select
Register (BRSR)
0
1
1
1
0
Modem Status Register
(MSR)
→
Data Bus
D7 D6 D5 D4 D3 D2 D1 D0
Stop Bit
Select
0 = 1 Stop Bits
1 = 1.5 Stop Bits (Tx)
and 1 Stop Bit (Rx)
If 5 Data Bits Selected
1 = 2 Stop Bits for 6, 7
or 8 Data Bits Selected
Parity
Control
000 = Tx and Rx Even
001 = Tx and Rx Odd
010 = Tx Even, Rx
Odd
011 = Tx Odd, Rx
Even
100 = Tx Even, Rx
Check Disabled
101 = Tx Odd, Rx
Check Disabled
11X = Generation and
Check Disabled
Word
Length
Select
00 = 5 Bits
01 = 6 Bits
10 = 7 Bits
11 = 8 Bits
Reserved Set to 00 for Future
Product Upgrade
Compatibility
FIGURE 1. UCR
82C52
相关PDF资料 |
PDF描述 |
|---|---|
| IS82C54 | CMOS Programmable Interval Timer |
| IS82C54-10 | CMOS Programmable Interval Timer |
| IS82C54-12 | CMOS Programmable Interval Timer |
| IS82C82 | CMOS Octal Latching Bus Driver |
| IS82C83H | CMOS Octal Latching Inverting Bus Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IS82C52/TR100/BAE | 制造商:Intersil Corporation 功能描述:PERIPH UART/BRG 5V 16MHZ 28PLCC IND - Tape and Reel |
| IS82C5296 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C52R2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C52Z | 功能描述:UART 接口集成电路 W/ANNEAL PERIPH /BRG 5V 16MHZ RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| IS82C52Z96 | 功能描述:UART 接口集成电路 W/ANNEAL PERIPH /BRG 5V 16MHZ RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。