参数资料
| 型号： | ISL1219IUZ-T |
| 厂商： | Intersil |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC RTC LP BATT BACK SRAM 10MSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 2,500 |
| 类型： | 时间事件记录器 |
| 特点： | 警报器，闰年，SRAM |
| 存储容量： | 2B |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
20
FN6314.2
July 15, 2010
Application Section
Event Detection
The event detection feature of the ISL1219 is intended to be
used for recording the time of single events that involve the
opening of an enclosure, door, etc. The normal method of
detection is with normally closed switch function that opens
to initiate the event. This mechanism is ideal for applications
such as set top boxes, utility meters, security alarm and
camera systems or vending machines.
A typical application diagram is shown in Figure 19. A
microcontroller communicates with the ISL1219 through the
I2C serial bus, to set up and read time of the day, alarms, or
set up the outputs frequency control.
The ISL1219 is capable of recording individual event
time/dates using the on-chip registers (Event Registers,
addresses 14h to 19h). Single event times are recorded and
can be read using a multiple address read, similar to reading
the RTC registers. The Event Registers record the initial
event time of a series of events, until the EVT bit is reset.
After EVT is reset, the Timestamp Registers retain the
previous event time until the next Event happens, at which
time the current RTC register contents will be placed in the
Event Registers. The Timestamp Registers cannot be
cleared, only a full power down cycle (VCC and VBAT = 0V)
will erase their contents.
For example, the event function is enabled and the EVT bit
in the Status Register is cleared. Then the EVEN pin is
triggered 3 times before the timestamp register is read. Only
the first Event time will be recorded in the Timestamp
Registers, and will be read. Then the EVT bit is cleared in
the Status Register, and two more events happen. The
previous Timestamp contents are replaced by the time of the
next event after the EVT bit reset.
An additional event action available in the ISL1219 is to stop
the real time clock from advancing. If the event register is set
to enable this function (Register 09h, RTCHLT bit 5 set to 1),
then when the EVIN pin is triggered, the clock counters will
stop and hold the time of the event. This is useful for one
time occurrences such as opening a warranted consumer
product enclosure or exceeding a maximum temperature
inside a device. Once the clock is stopped, the clock
registers must be written with an updated time, then they will
begin advancing immediately. If the RTCHLT bit is still set,
then the next event will again stop the clock.
Event Detect Input Details
The EVIN input is a Schmitt trigger logic input. An event is
detected when it is asserted high. The ISL1219 device has
internal configuration settings which add detection flexibility.
There are four configuration bits in register 09h which are for
EVIN sampling. The ESMP1 and ESMP0 bits control
sampling of the event input status. Reducing the sampling
rate will lower the supply current drain, with the tradeoff of
adding a delay in detecting an event. An event that is long in
duration (i.e. opening a door) would obviously be served well
with the lowest frequency sampling rate and lowest supply
current drain.
The EHYS1 and EHYS0 bits control timer circuits to filter out
switch bouncing, noise or intermittent contacts, by effectively
adding time-based hysteresis to the EVIN input. They are
used only in conjunction with the sampling rate, they cannot
be used alone. The most appropriate use for the hysteresis
function is for glitch or noise filtering on the EVIN input
signal.
P0
P2
P4
P1
P3
P5
SCL
SDA
X1
X2
VBAT
VDD
EVIN
VCC
IRQ/F
SCL
SDA
EVDET
ISL1219
MICRO C.
Note: Event Detect Switch Normally Closed
VCC
5.1k
5.1k+
1M**
2M*
3.0V
32.768kHz
Source
* Optional Pull-up resistors, or use internal current
** The Pull-up resistor on the EVDET-output can vary
from 10k up to 10M or more, depending on the
application
10
9
8
7
6
1
2
3
4
5
FIGURE 19.
ISL1219
相关PDF资料 |
PDF描述 |
|---|---|
| ISL1220IUZ | IC RTC LP BATT BACK SRAM 10MSOP |
| ISL1221IUZ | IC RTC LP BATT BACK SRAM 10MSOP |
| ISL26134AVZ | IC ADC 24BIT SRL 80SPS 28TSSOP |
| ISL26319FVZ-T7A | IC ADC 12BIT SRL/SPI 16TSSOP |
| ISL26329FVZ | IC ADC 12BIT SPI/SRL 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL1220 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:I2C㈢ Real Time Clock/Calendar with Frequency Output |
| ISL1220IUZ | 功能描述:实时时钟 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1220IUZ-T | 功能描述:实时时钟 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1221 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Power RTC with Battery Backed |
| ISL1221IUZ | 功能描述:实时时钟 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。