- 您现在的位置：买卖IC网 > PDF目录383129 > ISL29003 (Intersil Corporation) Light-to-Digital Output Sensor with High Sensitivity, Gain Selection, Interrupt Function and I2C Interface(具有高灵敏度，增益可选，中断功能和I2C接口的光电输出传感器) PDF资料下载
参数资料
| 型号： | ISL29003 |
| 厂商： | Intersil Corporation |
| 英文描述： | Light-to-Digital Output Sensor with High Sensitivity, Gain Selection, Interrupt Function and I2C Interface(具有高灵敏度，增益可选，中断功能和I2C接口的光电输出传感器) |
| 中文描述： | 光到数字输出传感器灵敏度高，增益选择，中断功能和I2C接口（具有高灵敏度，增益可选，中断功能和的I2C接口的光电输出传感器） |
| 文件页数： | 3/15页 |
| 文件大小： | 258K |
| 代理商： | ISL29003 |
3
FN7464.3
October 8, 2007
Principles of Operation
Photodiodes
The ISL29003 contains two photodiodes. Diode1 is sensitive
to both visible and infrared light, while Diode2 is mostly
sensitive to infrared light. The spectral response of the two
diodes are independent from one another. See Figure 8
Spectral Response vs Wavelength in the performance curves
section. The photodiodes convert light to current. Then, the
diodes’ current outputs are converted to digital by a single
built-in integrating type 16-bit Analog-to-Digital Converter
(ADC). An
I
2
C command mode determines which photodiode
will be converted to a digital signal. Mode1 is Diode1 only.
Mode2 is Diode2 only. Mode3 is a sequential Mode1 and
Mode2 with an internal subtract function (Diode1 - Diode2).
Analog-to-Digital Converter (ADC)
The converter is a charge-balancing integrating type 16-bit
ADC. The chosen method for conversion is best for
converting small current signals in the presence of an AC
periodic noise. A 100ms integration time, for instance, highly
rejects 50Hz and 60Hz power line noise simultaneously. See
“Integration Time or Conversion Time” on page 8 and “Noise
Rejection” on page 9.
The built-in ADC offers user flexibility in integration time or
conversion time. Two timing modes are available; Internal
Timing Mode and External Timing Mode. In Internal Timing
Mode, integration time is determined by an internal dual speed
oscillator (f
OSC
), and the n-bit (n = 4, 8, 12,16) counter inside
the ADC. In External Timing Mode, integration time is
determined by the time between two consecutive I
2
C External
Timing Mode commands. See “External Timing Mode” on
page 7. A good balancing act of integration time and resolution
depending on the application is required for optimal results.
The ADC has four I
2
C programmable range select to
dynamically accommodate various lighting conditions. For
very dim conditions, the ADC can be configured at its lowest
range. For very bright conditions, the ADC can be configured
at its highest range.
Interrupt Function
The active low interrupt pin is an open drain pull-down
configuration. The interrupt pin serves as an alarm or
monitoring function to determine whether the ambient light
exceeds the upper threshold or goes below the lower
threshold. The user can also configure the persistency of the
interrupt pin. This eliminates any false triggers such as noise
or sudden spikes in ambient light conditions. An unexpected
camera flash for example can be ignored by setting the
persistency to 8 integration cycles.
I
2
C Interface
There are eight (8) 8-bit registers available inside the ISL29003.
The command and control registers define the operation of the
device. The command and control registers do not change until
the registers are overwritten.There are two 8-bit registers that
set the high and low interrupt thresholds. There are four 8-bit
data Read Only registers; two bytes for the sensor reading and
another two bytes for the timer counts. The data registers
contain the ADC's latest digital output, and the number of clock
cycles in the previous integration period.
The ISL29003’s I
2
C interface slave address is hardwired
internally as 1000100. When 1000100x with x as R or W is
sent after the Start condition, this device compares the first
seven bits of this byte to its address and matches.
Figure 1 shows a sample one-byte read. Figure 2 shows a
sample one-byte write. Figure 3 shows a sync_iic timing
diagram sample for externally controlled integration time.
The I
2
C bus master always drives the SCL (clock) line, while
either the master or the slave can drive the SDA (data) line.
Figure 2 shows a sample write. Every I
2
C transaction begins
with the master asserting a start condition (SDA falling while
SCL remains high). The following byte is driven by the
master and includes the slave address and read/write bit.
The receiving device is responsible for pulling SDA low
during the acknowledgement period.
Every I
2
C transaction ends with the master asserting a stop
condition (SDA rising while SCL remains high).
For more information about the I
2
C standard, please consult
the Philips
I
2
C specification documents.
Pin Descriptions
PIN NUMBER
PIN NAME
DESCRIPTION
1
VDD
Positive supply; connect this pin to a regulated 2.5V to 3.3V supply
2
GND
Ground pin. The thermal pad is connected to the GND pin
3
REXT
External resistor pin for ADC reference; connect this pin to ground through a (nominal) 100k
Ω
resistor
4
INT
Interrupt pin; LO for interrupt/alarming. The INT pin is an open drain.
5
SCL
I
2
C serial clock
The I
2
C bus lines can pulled above VDD, 5.5V max.
6
SDA
I
2
C serial data
ISL29003
相关PDF资料 |
PDF描述 |
|---|---|
| ISL36356A-APDK-EVAL | PRISM 11Mbps Wireless Local Area Network Access Point |
| ISL36356A-APDK | PRISM 11Mbps Wireless Local Area Network Access Point |
| ISL3690IR-TK | Dual Band Direct Conversion Transceiver |
| ISL3690IR | Dual Band Direct Conversion Transceiver |
| ISL3690 | DIODE ZENER SINGLE 1000mW 7.5Vz 34mA-Izt 0.05 10uA-Ir 5Vr DO41-GLASS 5K/REEL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL29003IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29003IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29003 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL29003IROZ-T7 | 功能描述:光学数位转换器 ISL29003IROZ LIGHT-T O-DIGTL I2C GAIN RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel |
| ISL29004IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 8-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29004IROZ-EVALZ | 制造商:Intersil Corporation 功能描述:INTRFC LIGHT-TO-DGTL OUTPUT SENSOR - Bulk |
发布紧急采购，3分钟左右您将得到回复。