- 您现在的位置：买卖IC网 > PDF目录383129 > ISL29003 (Intersil Corporation) Light-to-Digital Output Sensor with High Sensitivity, Gain Selection, Interrupt Function and I2C Interface(具有高灵敏度，增益可选，中断功能和I2C接口的光电输出传感器) PDF资料下载
参数资料
| 型号： | ISL29003 |
| 厂商： | Intersil Corporation |
| 英文描述： | Light-to-Digital Output Sensor with High Sensitivity, Gain Selection, Interrupt Function and I2C Interface(具有高灵敏度，增益可选，中断功能和I2C接口的光电输出传感器) |
| 中文描述： | 光到数字输出传感器灵敏度高，增益选择，中断功能和I2C接口（具有高灵敏度，增益可选，中断功能和的I2C接口的光电输出传感器） |
| 文件页数： | 9/15页 |
| 文件大小： | 258K |
| 代理商： | ISL29003 |
9
FN7464.3
October 8, 2007
INTEGRATION TIME IN EXTERNAL TIMING MODE
This timing mode is programmed in the command register
00(hex) bit 5. External Timing Mode is recommended when
integration time can be synchronized to an external signal
such as a PWM to eliminate noise.
For Mode1 or Mode2 operation, the integration starts when
the sync_iic command is sent over the I
2
C lines. The device
needs two sync_iic commands to complete a photodiode
conversion. The integration then stops when another
sync_iic command is received. Writing a logic 1 to the
sync_iic bit ends the current adc integration and starts
another one.
For Mode3, the operation is a sequential Mode1 and Mode2.
The device needs three sync_iic commands to complete two
photodiode measurements. The 1st sync_iic command starts
the conversion of the diode1. The 2nd sync_iic completes the
conversion of diode1 and starts the conversion of diode2. The
3rd sync_iic pulse ends the conversion of diode2 and starts
over again to commence conversion of diode1.
The integration time, t
int
, is determined by Equation 12:
i
I2C
i
I2C
is the number of I
2
C clock cycles to obtain the t
int.
f
I2C
is the I
2
C operating frequency.
The internal oscillator, f
OSC
, operates identically in both the
internal and external timing modes, with the same
dependence on R
EXT
. However, in External Timing Mode,
the number of clock cycles per integration is no longer fixed
at 2
n
. The number of clock cycles varies with the chosen
integration time, and is limited to 2
16
= 65,536. In order to
avoid erroneous lux readings the integration time must be
short enough not to allow an overflow in the counter register.
f
OSC
= 327kHz*100k
Ω
/R
EXT
. When Range/Gain is set to
Range1 or Range2.
f
OSC
= 655kHz*100k
Ω
/R
EXT
. When Range/Gain is set to
Range3 or Range4.
Noise Rejection
In general, integrating type ADC’s have an excellent noise-
rejection characteristics for periodic noise sources whose
frequency is an integer multiple of the integration time. For
instance, a 60Hz AC unwanted signal’s sum from 0ms to
k*16.66ms (k = 1,2...k
i
) is zero. Similarly, setting the device’s
integration time to be an integer multiple of the periodic
noise signal, greatly improves the light sensor output signal
in the presence of noise.
DESIGN EXAMPLE 1
The ISl29003 will be designed in a portable system. The
ambient light conditions that the device will be exposed to is
at most 500 lux which is a good office lighting. The light
source has a 50/60Hz power line noise which is not visible
by the human eye. The I
2
C clock is 10kHz.
Solution -
Using Internal Timing Mode
In order to achieve both 60Hz and 50Hz AC noise rejection,
the integration time needs to be adjusted to coincide with an
integer multiple of the AC noise cycle times.
t
int
= i(1/60Hz) = j(1/50Hz).
The first instance of integer values at which t
int
rejects both
60Hz and 50Hz is when i = 6, and j = 5.
t
int
= 6(1/60Hz) = 5(1/50Hz)
t
int
= 100ms
Next, the Gain/Range needs to be determined. Based on the
application condition given, lux(max) = 500 lux, a range of
1000 lux is desirable. This corresponds to a Gain/Range
Range1 mode. Also impose a resolution of n = 16-bit. Hence
we choose Equation 10 to determine R
EXT
.
×
×
k
Ω
2
The Full Scale Range, FSR, needs to be determined. From
Equation 3:
The effective transfer function becomes:
TABLE 13. INTEGRATION TIMES FOR TYPICAL R
EXT
VALUES
R
EXT
(k
Ω)
RANGE1
RANGE2
RANGE3
RANGE4
n = 16-BIT
n = 12-BIT
n = 12-BIT
n = 4
50
100
6.4
3.2
0.013
100**
200
13
6.5
0.025
200
400
26
13
0.050
500
1000
64
32
0.125
*Integration time in milliseconds
**Recommended R
EXT
resistor value
t
int
----------
=
(EQ. 12)
t
int
OSC
-----------------
<
(EQ. 13)
for Internal Timing Mode and Gain/Range is set to Range3 or Range4 only
R
EXT
t
------------------------------------------------------------
327kHz
100
=
R
EXT
50k
Ω
=
FSR
1000 lux50k
Ω
Ω
=
FSR
2000 lux
=
E
2
-------------
2000 lux
×
=
ISL29003
相关PDF资料 |
PDF描述 |
|---|---|
| ISL36356A-APDK-EVAL | PRISM 11Mbps Wireless Local Area Network Access Point |
| ISL36356A-APDK | PRISM 11Mbps Wireless Local Area Network Access Point |
| ISL3690IR-TK | Dual Band Direct Conversion Transceiver |
| ISL3690IR | Dual Band Direct Conversion Transceiver |
| ISL3690 | DIODE ZENER SINGLE 1000mW 7.5Vz 34mA-Izt 0.05 10uA-Ir 5Vr DO41-GLASS 5K/REEL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL29003IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29003IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29003 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL29003IROZ-T7 | 功能描述:光学数位转换器 ISL29003IROZ LIGHT-T O-DIGTL I2C GAIN RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel |
| ISL29004IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 8-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29004IROZ-EVALZ | 制造商:Intersil Corporation 功能描述:INTRFC LIGHT-TO-DGTL OUTPUT SENSOR - Bulk |
发布紧急采购，3分钟左右您将得到回复。