参数资料
| 型号： | ISL6115AEVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 1/10页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD 1 FOR ISL6115A |
| 标准包装： | 1 |
| 系列： | * |
12V Power Distribution Controllers
ISL6115A
This fully featured hot swap power controller targets
+12V applications. The ISL6115A with its integrated
charge pump has a higher (6.5V vs 5V) gate drive
than its sister part the ISL6115 making this part an
immediate efficiency improvement replacement.
This IC features programmable overcurrent (OC)
detection, current regulation (CR) with time delay to
latch-off and soft-start.
The current regulation level is set by 2 external
resistors; R ISET sets the CR Vth and the other is a
low ohmic sense resistor across, which the CR Vth is
developed. The CR duration is set by an external
capacitor on the CTIM pin, which is charged with a
20μA current once the CR Vth level is reached. The
IC then quickly pulls down the GATE output latching
off the pass FET.
Features
? HOT SWAP Single Power Distribution Control for
+12V
? Overcurrent Fault Isolation
? Programmable Current Regulation Level
? Programmable Current Regulation Time to
Latch-Off
? Rail-to-Rail Common Mode Input Voltage Range
? Enhanced Internal Charge Pump Drives N-Channel
MOSFET gate to 6.5V above IC bias.
? Undervoltage and Overcurrent Latch Indicators
? Adjustable Turn-On Ramp
? Protection During Turn-On
? Two Levels of Overcurrent Detection Provide Fast
Response to Varying Fault Conditions
? 1μs Response Time to Dead Short
? Pb-Free (RoHS Compliant)
Applications
? Power Distribution Control
? Hot Plug Components and Circuitry
Application Circuits - High Side Controller
1
+
8
LOAD
-
2
3
ISL6115A
7
6
PWRON
PGOOD
OC
4
+V SUPPLY TO BE CONTROLLED
5
+12V
April 23, 2010
FN6855.1
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright ? Intersil Americas Inc. 2008, 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6115EVAL1Z | EVAL BOARD ISL6115 |
| ISL6115EVAL1 | EVALUATION BOARD 12V ISL6115 |
| ISL6119USBEVAL1 | EVALUATION BOARD FOR ISL6119 |
| ISL6121EVAL1 | EVALUATION BOARD ISL6121 |
| ISL612XSEQEVAL1Z | EVALUATION BOARD ISL612XSEQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6115AIBZ | 功能描述:热插拔功率分布 W/ANNEAL 8LD+12V SNG HOT PLUG CONTRLR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6115AIBZ-T | 功能描述:热插拔功率分布 W/ANNEAL 8LD +12V HOT PLUG CNTRLR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6115AIBZ-T7A | 功能描述:热插拔功率分布 Pb-Free w/Anneal 8 LD SOIC, +12V SINGLE HOT PLUG CONTROLLER, RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6115CB | 功能描述:IC MANAGER POWER HOT SWAP 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6115CB-T | 功能描述:IC CTRLR POWER DISTRIB 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。