- 您现在的位置：买卖IC网 > PDF目录20329 > ISL6144IRZA (Intersil)IC CTRLR O-RING MOSFET HV 20-QFN PDF资料下载
参数资料
| 型号： | ISL6144IRZA |
| 厂商： | Intersil |
| 文件页数： | 23/30页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR O-RING MOSFET HV 20-QFN |
| 标准包装： | 60 |
| 应用： | 电信/数据通信系统 |
| FET 型： | N 沟道 |
| 输出数： | 1 |
| 内部开关： | 无 |
| 延迟时间 - 开启： | 1ms |
| 延迟时间 - 关闭： | 250ns |
| 电源电压： | 9 V ~ 75 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
| 产品目录页面： | 1243 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页
ISL6144
This shows that worst-case failure scenario has to be
accounted for when choosing the ORing MOSFET. In both
cases, more than one ORing MOSFET/diode has to be
paralleled on each feed. Using parallel devices reduces
power dissipation per device and limits the junction
temperature rise to acceptable safe levels. Another
alternative is to choose a MOSFET with lower r DS(ON)
(Refer to Tables 1 and 2 for some examples).
If parallel MOSFETs are used on each feed, make sure to
use the same part number. Also it is preferable to have parts
from the same lot to insure load sharing between these
paralleled devices.
The final choice of the N-Channel ORing MOSFET depends
on the following aspects:
? Voltage Rating: The drain-source breakdown voltage
V DSS has to be higher than the maximum input voltage,
including transients and spikes. Also, the gate to source
voltage rating has to be considered. The ISL6144
maximum Gate charge voltage is 12V. Make sure the used
MOSFET has a maximum V GS rating >12V.
? Power Losses: In this application, the ORing MOSFET is
used as a series pass element, which is normally fully
enhanced at high load currents. Switching losses are
negligible. The major losses are conduction losses, which
depend on the value of the on-state resistance of the
MOSFET r DS(ON) , and the per feed load current. For an
N + 1 redundant system with perfect current sharing, the
? Current handling capability, steady state and peak, are
also two important parameters that must be considered.
The limitation on the maximum allowable drain current
comes from limitation on the maximum allowable device
junction temperature. The thermal board design has to be
able to dissipate the resulting heat without exceeding the
MOSFET’s allowable junction temperature.
Suppose P Loss = 1W in a D2PAK MOSFET, junction to
ambient thermal resistance R θ JA = +43°C/W (with 1 inch 2
copper pad area), T JMAX = +175°C, r DS(ON) = 4.5m Ω ,
maximum ambient board temperature = +85°C.
We need to make sure that the MOSFET’s junction
temperature during operation does not exceed the maximum
allowable device junction temperature.
T J = T A_max + P Loss ? R θ JA
T J = +85°C+1W. +43°C/W = +128°C
T J < T JMAX
In the example of Figure 30 with a load of 32A, at least 3
MOSFETs with r DS(ON) = 4.5m Ω are paralleled to limit the
dissipation to below 1W and operate with safe junction
temperature.
Tables 1 and 2 show MOSFET selection for some typical
applications with different input voltages and load currents in
a 1 + 1 redundant power system (a maximum of 1W of
power dissipation across each MOSFET is assumed).
P loss ( FET ) = ? ----------------- ? ? r DS ( ON )
per feed MOSFET losses are:
I LOAD 2
? N + 1 ?
(EQ. 14)
For a 48V Input:
TABLE 1. INPUT VOLTAGE = 48V
? The final MOSFET selection has to be based on the worse
case current when the system is reduced to N parallel
supplies due to a permanent failure of one unit. The
remaining units have to provide the full load current. In this
case, losses across each remaining ORing MOSFET
become Equation 15:
I Load_Max
8A
16A
MOSFET PART NUMBER
FDB3632 (Note 14)
SUM110N10-08 (Note 15)
FDB3632 (Note 14)
SUM110N10-08
FDB045AN08A0 (Note 16)
N (Note 13)
1
1
2
2
1
P loss ( FET ) = ? ----------------- ? ? r DS ( ON )
? N ?
I LOAD 2
(EQ. 15)
32A
FDB3632 (Note 14)
SUM110N10-08
FDB045AN08A0
4
4
3
? In the particular cases illustrated in the previous examples
of Figures 29 and 30 with N = 1, each of the two ORing
feeds have to be able to handle the full load current.
? The MOSFET’s r DS(ON) value also depends on junction
temperature; a curve showing this relationship is usually
part of any MOSFET’s data sheet. The increase in the
value of the r DS(ON) over-temperature has to be taken into
account.
23
NOTES:
13. Number of parallel MOSFETs per feed
14. V DSS = 100V;I D = 80A; r DS(ON) = 9m Ω
15. V DSS = 100V; I D = 110A; r DS(ON) = 9.5m Ω
16. V DSS = 75V; I D = 80A; r DS(ON) = 4.5m Ω
FN9131.7
October 6, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6146BFRZ-T7A | IC OR CTRLR N-CH 1CH 8DFN |
| B170B-13 | DIODE SCHOTTKY 70V 1A SMB |
| A470K15C0GL5UAA | CAP CER 47PF 500V 10% NP0 AXIAL |
| ISL6144IVZA-T | IC CTRLR MOSFET HV ORING 16TSSOP |
| EBM12DTAD-S189 | CONN EDGECARD 24POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6144IRZA-T | 功能描述:IC CTRLR MOSFET HV ORING 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL6144IV | 功能描述:IC CTRLR MOSFET ORING HV 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL6144IV-T | 功能描述:IC CTRLR MOSFET HV ORING 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL6144IVZA | 功能描述:IC CTRLR MOSFET ORING HV 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL6144IVZA-T | 功能描述:IC CTRLR MOSFET HV ORING 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。