- 您现在的位置：买卖IC网 > PDF目录16625 > ISL6218CVZ-T (Intersil)IC CTRLR INTEL PENT M 38-TSSOP PDF资料下载
参数资料
| 型号： | ISL6218CVZ-T |
| 厂商： | Intersil |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR INTEL PENT M 38-TSSOP |
| 标准包装： | 2,500 |
| 应用： | 处理器 |
| 电流 - 电源： | 1.4mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -10°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 带卷 (TR) |
ISL6218
to the Processor power pins; they are placed carefully so they
do not to add inductance in the circuit board traces, which could
cancel the usefulness of these low inductance components.
Specialized low-ESR capacitors intended for switching
regulator applications are recommended for the bulk
capacitors. The bulk capacitors ESR and ESL determine the
output ripple voltage and the initial voltage drop following a
high slew-rate transient edge. Recommended are at least (4)
4V, 220μF Sanyo Sp-Cap capacitors in parallel, or (5) 330μF
SP-Cap style capacitors. These capacitors provide an
equivalent ESR of less than 3m Ω . These components
should be laid out very close to the load.
As the sense trace for VSEN may be long and routed close
to switching nodes, a 1.0μF ceramic decoupling capacitor is
located between VSEN and ground at the ISL6218 package.
Output Inductor Selection
The output inductor is selected to meet the voltage ripple
requirements and minimize the converter response time to a
load transient.
The inductor selected for the power channel determines the
channel ripple current. Increasing the value of inductance
reduces the total output ripple current and total output
voltage ripple, but will slow the converter response time to a
load transient.
One of the parameters limiting the converter’s response time to
MOSFET Selection and Considerations
For the Intel IMVP-IV ? application that requires up to 20A of
current, it is suggested that Single-Phase channel operation,
with a minimum of (4) MOSFETs per channel, be
implemented. This configuration would be: (2) High
Switching Frequency, Low Gate Charge MOSFET for the
Upper; and (2) Low r DS(ON) MOSFETs for the Lowers.
In high-current PWM applications, the MOSFET power
dissipation, package selection and heatsink are the
dominant design factors. The power dissipation includes two
loss components: conduction loss and switching loss. These
losses are distributed between the upper and lower
MOSFETs according to duty cycle of the converter. Refer to
Equations 8 and 9. The conduction losses are the main
component of power dissipation for the lower MOSFETs.
Only the upper MOSFETs have significant switching losses,
since the lower devices turn on and off into near zero
voltage. The following equations assume linear voltage-
current transitions and do not model power loss due to the
reverse-recovery of the lower MOSFET’s body diode. The
gate-charge losses are dissipated in the ISL6218 drivers and
do not heat the MOSFETs; however, large gate-charge
increases the switching time t SW , which increases the upper
MOSFET switching losses. Ensure that both MOSFETs are
within their maximum junction temperature at high ambient
temperature by calculating the temperature rise according to
package thermal-resistance specifications.
I × V IN × t SW × F SW
a load transient is the time required to slew the inductor current
from its initial current level to the transient current level. During
this interval, the difference between the two levels must be
supplied by the output capacitance. Minimizing the response
P UPPER =
I O 2 × r DS ( ON ) × V OUT
V IN
+ O
2
(EQ. 8)
time can minimize the output capacitance required.
Δ I CH = IN
V ? V OUT V
The channel ripple current is approximated by Equation 7:
? OUT (EQ. 7)
F SW ? L V IN
P LOWER =
I O 2 × r DS ( ON ) × ( V IN ? V OUT )
V IN
(EQ. 9)
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use ceramic capacitors for
the high frequency decoupling and bulk capacitors to supply
the RMS current. Small ceramic capacitors must be placed
very close to the upper MOSFET to suppress the voltage
induced in the parasitic circuit impedances.
Two important parameters to consider when selecting the
bulk input capacitor are the voltage rating and the RMS
current rating. For reliable operation, select a bulk capacitor
with voltage and current ratings above the maximum input
voltage and largest RMS current required by the circuit. The
capacitor voltage rating should be at least 1.25 times greater
than the maximum input voltage and a voltage rating of 1.5
times is a conservative guideline.
16
Typical Application - Single Phase
Converter Using ISL6218 PWM Controller
Figure 12 shows the ISL6218, Synchronous Buck Converter
circuit, which is used to provide the CORE voltage regulation
for the Intel IMVP-IV ? application. The circuit uses a single
power channel to deliver up to 20A steady state current, and
has a 330kHz channel switching frequency. For thermal
compensation, a PTC resistor is used as sense resistors.
The Output capacitance is less than 3m Ω of ESR and is (4)
220μF, 4V Sp-Cap parts in parallel with (35) high frequency,
10μF ceramic capacitors.
FN9101.6
August 6, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ELC-18B220L | COIL CHOKE 22UH RADIAL |
| ELC-18B180L | COIL CHOKE 18UH RADIAL |
| GCA32DRMS | CONN EDGECARD 64POS .125 SQ WW |
| EEU-FR1E102LB | CAP ALUM 1000UF 25V 20% RADIAL |
| ELC-18B150L | COIL CHOKE 15UH RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6218EVAL2 | 功能描述:EVALUATION BOARD 2 FOR ISL6218 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6219 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications |
| ISL6219 WAF | 制造商:Harris Corporation 功能描述: |
| ISL6219A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications |
| ISL6219A_07 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Precision Multi-Phase BUCK PWM Controller for Mobile Applications |
发布紧急采购，3分钟左右您将得到回复。