- 您现在的位置：买卖IC网 > PDF目录15047 > ISL6219ACAZ (Intersil)IC REG CTRLR BUCK PWM VM 28-QSOP PDF资料下载
参数资料
| 型号： | ISL6219ACAZ |
| 厂商： | Intersil |
| 文件页数： | 8/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 28-QSOP |
| 标准包装： | 48 |
| PWM 型： | 电压模式 |
| 输出数： | 3 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -10°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
ISL6219A
The converter depicted in Figure 3 delivers 36A to a 1.5V
load from a 12V input. The RMS input capacitor current is
V IN
SEN = I L --------------------------
5.9A. Compare this to a single-phase converter also down
12V to 1.5V at 36A. The single-phase converter has 11.9A
rms input capacitor current. The single-phase converter
I n
I
r DS ( ON )
R ISEN
CHANNEL N
UPPER MOSFET
R ISEN
L DS ( ON )
must use an input capacitor bank with twice the RMS current
capacity as the equivalent three-phase converter.
Figures 14 and 15 in the section entitled can be used to
determine the input-capacitor rms current based on load
current, duty cycle, and the number of active channels. They
are provided as aids in determining the optimal input
capacitor solution. Figure 16 shows the single phase input-
SAMPLE
&
HOLD
-
+
ISEN(n)
-
I
+
CHANNEL N
LOWER MOSFET
r
I L
capacitor rms current for comparisson.
ISL6219A INTERNAL CIRCUIT
EXTERNAL CIRCUIT
PWM OPERATION
The number of active channels selected determines the
timing for each channel. By default, the timing mode for the
ISL6219A is 3-phase. The designer can select 2-phase
timing by connecting PWM3 to VCC.
One switching cycle for the ISL6219A is defined as the time
between PWM1 pulse termination signals (the internal signal
that initiates a falling edge on PWM1). The cycle time is the
inverse of the switching frequency selected by the resistor
connected between the FS/EN pin and ground (see
Switching Frequency ). Each cycle begins when a clock signal
commands the channel-1 PWM output to go low. This
signals the channel-1 MOSFET driver to turn off the channel-
1 upper MOSFET and turn on the channel-1 synchronous
MOSFET. If two-channel operation is selected, the PWM2
pulse terminates 1/2 of a cycle later. If three channels are
selected the PWM2 pulse terminates 1/3 of a cycle after
PWM1, and the PWM3 output will follow after another 1/3 of
a cycle.
Once a channel’s PWM pulse terminates, it remains low for
a minimum of 1/4 cycle. This forced off time is required to
assure an accurate current sample as described in Current
controller enables the PWM output. Once enabled, the PWM
output transitions high when the sawtooth signal crosses the
adjusted error-amplifier output signal, V COMP as illustrated
in Figures 1 and 5. This is the signal for the MOSFET driver
to turn off the synchronous MOSFET and turn on the upper
MOSFET. The output will remain high until the clock signals
the beginning of the next cycle by commanding the PWM
pulse to terminate.
CURRENT SENSING
Intersil multi-phase controllers sense current by sampling the
voltage across the lower MOSFET during its conduction
interval. MOSFET r DS(ON) sensing is a no-added-cost
method to sense current for load-line regulation, channel-
current balance, module current sharing, and overcurrent
protection. If desired, an independent current-sense resistor
in series with the lower-MOSFET source can serve as a
sense element in place of the MOSFET r DS(ON).
8
FIGURE 4. INTERNAL AND EXTERNAL CURRENT-SENSING
CIRCUITRY
The ISEN input for each channel uses a ground-referenced
amplifier to reproduce a signal proportional to the channel
current (Figure 4). After sufficient settling time, the sensed
current is sampled, and the sample is used for current
balance, load-line regulation and overcurrent protection. The
ISL6219A samples channel current once each cycle.
Figure 4 shows how the sampled current, I n , is created from
the channel current I L . The circuitry in Figure 4 represents
the current measurement and sampling circuitry for channel
n in an N-channel converter. This circuitry is repeated for
each channel in the converter but will not be active in
unused channels .
CHANNEL-CURRENT BALANCE
Another benefit of multi-phase operation is the thermal
advantage gained by distributing the dissipated heat over
multiple devices and greater area. By doing this, the
designer avoids the complexity of driving multiple parallel
MOSFETs and the expense of using expensive heat sinks
and exotic magnetic materials.
In order to fully realize the thermal advantage, it is important
that each channel in a multi-phase converter be controlled to
deliver about the same current at any load level. Intersil
multi-phase controllers guarantee current balance by
comparing each channel’s current to the average current
delivered by all channels and making an appropriate
adjustment to each channel’s pulse width based on the error.
Intersil’s patented current-balance method is illustrated in
Figure 5 where the average of the 2 or 3 sampled channel
currents combines with the channel 1 sample, I 1 , to create
an error signal I ER . The filtered error signal modifies the
pulse width commanded by V COMP to correct any
unbalance and force I ER toward zero.
FN9093.1
March 20, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| B82464Z4474M | INDUCTOR POWER 470UH .50A SMD |
| H2AXG-10112-Y4-ND | JUMPER-H1503TR/A2015Y/X 12" |
| B82464Z4473M | INDUCTOR POWER 47UH 1.55A SMD |
| H2AXG-10112-W4-ND | JUMPER-H1503TR/A2015W/X 12" |
| H2AXG-10112-V4-ND | JUMPER-H1503TR/A2015V/X 12" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6219ACAZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6219CA | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ISL6219CA-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6220DWF2E WAF | 制造商:Harris Corporation 功能描述: |
| ISL6223 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Mobile Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
发布紧急采购，3分钟左右您将得到回复。