参数资料
| 型号： | ISL6236AIRZ-T |
| 厂商： | Intersil |
| 文件页数： | 35/37页 |
| 文件大小： | 0K |
| 描述： | IC MAIN PWR CTRLR QUAD 32-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 4.5 V ~ 25 V |
| 输出数： | 4 |
| 输出电压： | 多重 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页
ISL6236A
while both switches are off (dead time). The drop is
where V DROP1 and V DROP2 are the parasitic voltage drops
I L ? r DS ( ON )
when the low-side switch conducts.
The rectifier is a clamp across the synchronous rectifier that
catches the negative inductor swing during the dead time
between turning the high-side MOSFET off and the
synchronous rectifier on. The MOSFETs incorporate a
high-speed silicon body diode as an adequate clamp diode if
efficiency is not of primary importance. Place a Schottky
diode in parallel with the body diode to reduce the forward
voltage drop and prevent the Q 2 /Q 4 MOSFET body diodes
from turning on during the dead time. Typically, the external
diode improves the efficiency by 1% to 2%. Use a Schottky
diode with a DC current rating equal to one-third of the load
current. For example, use an MBR0530 (500mA-rated) type
for loads up to 1.5A, a 1N5817 type for loads up to 3A, or a
1N5821 type for loads up to 10A. The rectifier's rated
Specifications” table on page 6 and K is taken from Table 2.
The absolute minimum input voltage is calculated with h = 1.
Operating frequency must be reduced or h must be
increased and output capacitance added to obtain an
acceptable V SAG if calculated V IN(MIN) is greater than the
required minimum input voltage. Calculate V SAG to be sure
of adequate transient response if operation near dropout is
anticipated.
Dropout Design Example:
ISL6236A: With V OUT2 = 5V, fsw = 400kHz, K = 2.25μs,
t OFF(MIN) = 350ns, V DROP1 = V DROP2 = 100mV, and
h = 1.5, the minimum V IN is:
V IN ( MIN ) = ---------------------------------------------- + 0.1V – 0.1V = 6.65V
1 – ? ------------------------------- ?
V IN ( MIN ) = ----------------------------------------- + 0.1V – 0.1V = 6.04V
1 – ? -------------------------- ?
reverse breakdown voltage must be at least equal to the
maximum input voltage, preferably with a 20% derating
factor.
Applications Information
Dropout Performance
The output voltage-adjust range for continuous-conduction
operation is restricted by the nonadjustable 350ns (max)
minimum off-time one-shot. Use the slower 5V SMPS for the
( 5V + 0.1V )
0.35 μ s ? 1.5
? 2.25 μ s ?
Calculating with h = 1 yields:
( 5V + 0.1V )
0.35 μ s ? 1
? 2.25 μ s ?
(EQ. 24)
(EQ. 25)
higher of the two output voltages for best dropout
performance in adjustable feedback mode. The duty-factor
limit must be calculated using worst-case values for on- and
off-times, when working with low input voltages.
Manufacturing tolerances and internal propagation delays
introduce an error to the t ON K-factor. Also, keep in mind that
transient-response performance of buck regulators operated
close to dropout is poor, and bulk output capacitance must
often be added (see Equation 11 on page 33).
The absolute point of dropout occurs when the inductor
current ramps down during the minimum off-time ( Δ I DOWN )
as much as it ramps up during the on-time ( Δ I UP ). The ratio
h = Δ I UP / Δ I DOWN indicates the ability to slew the inductor
current higher in response to increased load, and must
always be greater than 1. As h approaches 1, the absolute
minimum dropout point, the inductor current is less able to
increase during each switching cycle and V SAG greatly
increases unless additional output capacitance is used.
A reasonable minimum value for h is 1.5, but this can be
adjusted up or down to allow trade-offs between V SAG,
output capacitance and minimum operating voltage. For a
given value of h, the minimum operating voltage can be
calculated in Equation 23:
Therefore, V IN must be greater than 6.65V. A practical input
voltage with reasonable output capacitance would be 7.5V.
PC Board Layout Guidelines
Careful PC board layout is critical to achieve minimal switching
losses and clean, stable operation. This is especially true when
multiple converters are on the same PC board where one
circuit can affect the other. Refer to the ISL6236 Evaluation Kit
Application Notes (AN1271 and AN1272) for a specific layout
example.
Mount all of the power components on the top side of the board
with their ground terminals flush against one another, if
possible. Follow these guidelines for good PC board layout:
? Isolate the power components on the top side from the
sensitive analog components on the bottom side with a
ground shield. Use a separate PGND plane under the
OUT1 and OUT2 sides (called PGND1 and PGND2). Avoid
the introduction of AC currents into the PGND1 and PGND2
ground planes. Run the power plane ground currents on the
top side only, if possible.
? Use a star ground connection on the power plane to
minimize the crosstalk between OUT1 and OUT2.
? Keep the high-current paths short, especially at the
t OFF ( MIN ) ? h
1 – ? ------------------------------------ ?
( V OUT_ + V DROP )
V IN ( MIN ) = --------------------------------------------------- + V DROP2 – V DROP1
? K ?
35
(EQ. 23)
ground terminals. This practice is essential for stable,
jitter-free operation.
? Keep the power traces and load connections short. This
practice is essential for high efficiency. Using thick copper
PC boards (2oz vs 1oz) can enhance full-load efficiency
by 1% or more. Correctly routing PC board traces must be
FN6453.3
March 18, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| EBA32DTKT | CONN EDGECARD 64POS DIP .125 SLD |
| MIC5335-PGYMT TR | IC REG LDO 3V/1.8V .3A 6-MLF |
| ISL6236IRZA-TR5281 | IC MAIN PWR CTRLR QUAD 32-QFN |
| ESA18DTKS | CONN EDGECARD 36POS DIP .125 SLD |
| ISL6524ACBZA-T | IC CTRLR VRM8.5 PWM TRPL 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6236EVAL1 | 功能描述:EVAL BOARD 1 FOR ISL6236 RoHS:否 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:* 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ISL6236EVAL2 | 功能描述:EVAL BOARD 2 FOR ISL6236 RoHS:否 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:* 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ISL6236IRZA | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236IRZAR5281 | 功能描述:IC MAIN PWR CTRLR QUAD 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6236IRZA-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
发布紧急采购，3分钟左右您将得到回复。