- 您现在的位置：买卖IC网 > PDF目录16713 > ISL62381CHRTZ (Intersil)IC PWR SUPPLY CONTROLLER 32TQFN PDF资料下载
参数资料
| 型号： | ISL62381CHRTZ |
| 厂商： | Intersil |
| 文件页数： | 16/23页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY CONTROLLER 32TQFN |
| 标准包装： | 60 |
| 应用： | 电源控制器 |
| 输入电压： | 5.5 V ~ 25 V |
| 电源电压： | 5.5 V ~ 25 V |
| 电流 - 电源： | 150µA |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN（5x5） |
| 包装： | 管件 |
ISL62381, ISL62382, ISL62383, ISL62381C, ISL62382C, ISL62383C
transition is automatically achieved by detecting the load
current and turning off LGATE when the inductor current
reaches 0A.
Positive-going inductor current flows from either the source
Overcurrent Protection
The overcurrent protection (OCP) setpoint is programmed
with resistor, R OCSET , that is connected across the OCSET
and PHASE pins.
of the high-side MOSFET, or the drain of the low-side
MOSFET. Negative-going inductor current flows into the
drain of the low-side MOSFET. When the low-side MOSFET
conducts positive inductor current, the phase voltage will be
negative with respect to the GND and PGND pins.
Conversely, when the low-side MOSFET conducts negative
inductor current, the phase voltage will be positive with
respect to the GND and PGND pins. These controllers
PHASE1
ISL62381
10μA
OCSET1
DCR
+
R OCSET
+ V ROCSET
L
V DCR
C SEN
_
I L
_
V O
C O
V DCR = I L ? DCR
monitor the phase voltage when the low-side MOSFET is
conducting inductor current to determine its direction.
When the output load current is greater than or equal to ?
the inductor ripple current, the inductor current is always
positive, and the converter is always in CCM. These
controllers minimize the conduction loss in this condition by
forcing the low-side MOSFET to operate as a synchronous
rectifier.
When the output load current is less than ? the inductor
ripple current, negative inductor current occurs. Sinking
negative inductor current through the low-side MOSFET
lowers efficiency through unnecessary conduction losses.
These controllers automatically enter DEM after the PHASE
R O
ISEN1
FIGURE 26. OVERCURRENT-SET CIRCUIT
Figure 26 shows the overcurrent-set circuit for SMPS1. The
inductor consists of inductance L and the DC resistance
(DCR). The inductor DC current I L creates a voltage drop
across DCR, given by Equation 6:
(EQ. 6)
Theses controllers sink a 10μA current into the OCSET1 pin,
creating a DC voltage drop across the resistor R OCSET ,
given by Equation 7:
pin has detected positive voltage and LGATE was allowed to
go high for eight consecutive PWM switching cycles. These
V ROCSET = 10 μ A ? R OCSET
(EQ. 7)
controllers will turn off the low-side MOSFET once the phase
voltage turns positive, indicating negative inductor current.
These controllers will return to CCM on the following cycle
after the PHASE pin detects negative voltage, indicating that
the body diode of the low-side MOSFET is conducting
positive inductor current.
Resistor R O is connected between the ISEN1 pin and the
actual output of the converter. During normal operation, the
ISEN1 pin is a high impedance path, therefore there is no
voltage drop across R O . The DC voltage difference between
the OCSET1 pin and the ISEN1 pin can be established using
Equation 8:
Efficiency can be further improved with a reduction of
unnecessary switching losses by reducing the PWM
frequency. It is characteristic of the R 3 architecture for the
V OCSET1 – V ISEN1 = I L ? DCR – 10 μ A ? R OCSET
(EQ. 8)
PWM frequency to decrease while in diode emulation. The
extent of the frequency reduction is proportional to the
reduction of load current. Upon entering DEM, the PWM
frequency makes an initial step-reduction because of a 33%
step-increase of the window voltage V W .
These controllers monitor the OCSET1 pin and the ISEN1 pin
voltages. Once the OCSET1 pin voltage is higher than the
ISEN1 pin voltage for more than 10μs, these controllers
declare an OCP fault. The value of R OCSET is then written as
Equation 9:
Because the switching frequency in DEM is a function of
load current, very light load conditions can produce
frequencies well into the audio band. This can be
10 μ A
I OC ? DCR
R OCSET = ---------------------------
(EQ. 9)
problematic if audible noise is coupled into audio amplifier
circuits. To prevent this from occurring, these controllers
allow the user to float the FCCM input. This will allow DEM at
light loads, but will prevent the switching frequency from
going below ~28kHz to prevent noise injection into the audio
band. A timer is reset each PWM pulse. If the timer exceeds
30μs, LGATE is turned on, causing the ramp voltage to
reduce until another UGATE is commanded by the voltage
loop.
16
Where:
- R OCSET ( Ω ) is the resistor used to program the
overcurrent setpoint
- I OC is the output current threshold that will activate the
OCP circuit
- DCR is the inductor DC resistance
For example, if I OC is 20A and DCR is 4.5m Ω , the choice of
R OCSET is R OCSET = 20A x 4.5m Ω /10μA = 9k Ω.
FN6665.5
May 13, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| CB5409-000 | HEAT SHRINK TUBING |
| 234A132-4/42-0 | BOOT MOLDED |
| V375C12E150BF | CONVERTER MOD DC/DC 12V 150W |
| GCM18DRTH | CONN EDGECARD 36POS DIP .156 SLD |
| RNF-150-1/2-9-SP | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62381CHRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381HIEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62381HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62381HRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381HRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381LOEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62381LO RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。