- 您现在的位置：买卖IC网 > PDF目录16713 > ISL62381CHRTZ (Intersil)IC PWR SUPPLY CONTROLLER 32TQFN PDF资料下载
参数资料
| 型号： | ISL62381CHRTZ |
| 厂商： | Intersil |
| 文件页数： | 17/23页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY CONTROLLER 32TQFN |
| 标准包装： | 60 |
| 应用： | 电源控制器 |
| 输入电压： | 5.5 V ~ 25 V |
| 电源电压： | 5.5 V ~ 25 V |
| 电流 - 电源： | 150µA |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN（5x5） |
| 包装： | 管件 |
ISL62381, ISL62382, ISL62383, ISL62381C, ISL62382C, ISL62383C
Resistor R OCSET and capacitor C SEN form an RC network
to sense the inductor current. To sense the inductor current
correctly, not only in DC operation but also during dynamic
operation, the RC network time constant R OCSET C SEN
needs to match the inductor time constant L/DCR. The value
load from potentially damaging voltage levels. The LGATE
gate-driver will turn off the low-side MOSFET once the FB
pin voltage is lower than the falling overvoltage threshold for
more than 2μs. The falling overvoltage threshold is typically
106% of the reference voltage, or 1.06*0.6V = 0.636V. This
C SEN = -----------------------------------------
of C SEN is then written as Equation 10:
L
R OCSET ? DCR
(EQ. 10)
process repeats as long as the output voltage fault is
present, allowing the ISL62381, ISL62381C, ISL62383 and
ISL62383C to protect against persistent overvoltage
conditions.
For example, if L is 1.5μH, DCR is 4.5m Ω , and R OCSET is
9k Ω, the choice of C SEN = 1.5μH/(9k Ω x 4.5m Ω ) = 0.037μF .
Upon converter start-up, the C SEN capacitor bias is 0V. To
prevent false OCP during this time, a 10μA current source
flows out of the ISEN1 pin, generating a voltage drop on the
R O resistor, which should be chosen to have the same
resistance as R OCSET . When PGOOD pin goes high, the
ISEN1 pin current source will be removed.
When an OCP fault is declared, the PGOOD pin will
pull-down to 32 Ω and latch off the converter. The fault will
remain latched until the EN pin has been pulled below the
falling EN threshold voltage, or until V IN has decayed below
the falling POR threshold.
When using a discrete current sense resistor, inductor
time-constant matching is not required. Equation 7 remains
unchanged, but Equation 8 is modified in Equation 11:
For ISL62382 and ISL62382C, if OVP is detected, it simply tri-
states the PHASE node by turning UGATE and LGATE off.
Undervoltage Protection
The UVP fault detection circuit triggers after the FB pin
voltage is below the undervoltage threshold for more than
2μs. The undervoltage threshold is typically 86% of the
reference voltage, or 0.86*0.6V = 0.516V. If a UVP fault is
declared, and the PGOOD pin will pull-down with 93 Ω and
latch-off the converter. The fault will remain latched until the
EN pin has been pulled below the falling enable threshold, or
if V IN has decayed below the falling POR threshold.
Programming the Output Voltage
When the converter is in regulation, there will be 0.6V
between the FB and GND pins. Connect a two-resistor
voltage divider across the OUT and GND pins with the
output node connected to the FB pin, as shown in Figure 27.
V OCSET1 – V ISEN1 = I L ? R SENSE – 10 μ A ? R OCSET
Furthermore, Equation 9 is changed in Equation 12:
10 μ A
I OC ? R SENSE
R OCSET = -------------------------------------
(EQ. 11)
(EQ. 12)
Scale the voltage-divider network such that the FB pin is
0.6V with respect to the GND pin when the converter is
regulating at the desired output voltage. The output voltage
can be programmed from 0.6V to 5.5V.
Programming the output voltage is written as Equation 13:
V OUT = V REF ? ? 1 + ----------------------------- ?
Where R SENSE is the series power resistor for sensing
inductor current. For example, with an R SENSE = 1m Ω and
an OCP target of 10A, R OCSET = 1k Ω.
Where:
? R TOP ?
? R BOTTOM ?
(EQ. 13)
V REF ? R TOP
R BOTTOM = -------------------------------------
Overvoltage Protection
The OVP fault detection circuit triggers after the FB pin
voltage is above the rising overvoltage threshold for more
than 2μs. The FB pin voltage is 0.6V in normal operation.
The rising over voltage threshold is typically 116% of that
value, or 1.16*0.6V = 0.696V.
When an OVP fault is declared, the PGOOD pin will pull
down with 65 Ω and latch-off the converter. The OVP fault will
remain latched until the EN pin has been pulled below the
falling EN threshold voltage, or until V IN has decayed below
the falling POR threshold.
For ISL62381, ISL62381C, ISL62383 and ISL62383C,
although the converter has latched-off in response to an
OVP fault, the LGATE gate-driver output will retain the ability
to toggle the low-side MOSFET on and off in response to the
output voltage transversing the OVP rising and falling
thresholds. The LGATE gate-driver will turn on the low-side
MOSFET to discharge the output voltage, thus protecting the
17
- V OUT is the desired output voltage of the converter
- The voltage to which the converter regulates the FB pin
is the V REF (0.6V)
- R TOP is the voltage-programming resistor that connects
from the FB pin to the converter output. In addition to
setting the output voltage, this resistor is part of the loop
compensation network
- R BOTTOM is the voltage-programming resistor that
connects from the FB pin to the GND pin
Choose R TOP first when compensating the control loop, and
then calculate R BOTTOM according to Equation 14:
(EQ. 14)
V OUT – V REF
Compensation Design
Figure 27 shows the recommended Type-II compensation
circuit. The FB pin is the inverting input of the error amplifier.
The COMP signal, the output of the error amplifier, is inside the
chip and unavailable to users. C INT is a 100pF capacitor
FN6665.5
May 13, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| CB5409-000 | HEAT SHRINK TUBING |
| 234A132-4/42-0 | BOOT MOLDED |
| V375C12E150BF | CONVERTER MOD DC/DC 12V 150W |
| GCM18DRTH | CONN EDGECARD 36POS DIP .156 SLD |
| RNF-150-1/2-9-SP | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62381CHRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381HIEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62381HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62381HRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381HRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 32TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62381LOEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62381LO RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。