参数资料
| 型号： | ISL6260CCRZ |
| 厂商： | Intersil |
| 文件页数： | 22/28页 |
| 文件大小： | 0K |
| 描述： | IC REG PWM MULTI-PHASE 40-QFN |
| 标准包装： | 50 |
| 应用： | 转换器，Intel IMVP-6 |
| 输出数： | 1 |
| 输出电压： | 0.3 V ~ 1.5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页
ISL6260C
converter operating in CCM can be determined using the
following relationship, where Rfset is in k Ω and the switching
period is in μ s.
CPU operation and decrease the power consumption. When
the temperature goes down, the NTC thermistor voltage will
eventually go up. If NTC voltage increases to 1.24V, the
Rfset ( k Ω ) = ( Period ( μ s ) – 0.29 ) × 2.33
(EQ. 4)
comparator will then be able to flip back. The external
resistance difference in these two conditions is:
---------------- – ---------------- = 2.96k
In discontinuous conduction mode, (DCM), the ISL6260C
runs in period stretching mode. It should be noted that the
1.24V 1.20V
54 μ A 60 μ A
(EQ. 5)
switching frequency in the Electrical Specification Table is
tested with the error amplifier output or Comp pin voltage at
2V. When Comp pin voltage is lower, the switching
frequency will not be at the tested value but can still maintain
the output voltage ripple within spec.
Voltage Regulator Thermal Throttling
lntel? IMVP-6+? technology supports thermal throttling of
the processor to prevent catastrophic thermal damage to the
voltage regulator. The ISL6260C feature a thermal monitor
which senses the voltage change across an externally
placed negative temperature coefficient (NTC) thermistor,
see Figure 45. Proper selection and placement of the NTC
Therefore, proper NTC thermistor has to be chosen such
that 2.96k resistor change will be corresponding to required
temperature hysteresis. Regular external resistor may need
to be in series with NTC resistors to meet the threshold
voltage values.
The following is an example.
For Panasonic NTC thermistor with B = 4700, its resistance
will drop to 0.03322 of its nominal at +105°C, and drop to
0.03956 of its nominal at +100°C. If the requirement for the
temperature hysteresis is (+105°C to +100°C), the required
resistance of NTC will be:
------------------------------------------------------ = 467k Ω
thermistor allows for detection of a designated temperature
rise by the system.
2.96k Ω
( 0.03956 – 0.03322 )
(EQ. 6)
Figure 45 shows the thermal throttling feature with
hysteresis. At low temperature, SW1 is on and SW2
connects to the 1.20V side. The total current going from NTC
pin is 60μA. The voltage on NTC pin is higher than threshold
voltage of 1.20V and the comparator output is low. VR_TT#
is pulling up high by the external resistor.
Therefore a larger value thermistor, such as 470k NTC
should be used.
At 105°C, 470k NTC resistance becomes
(0.03322*470k) = 15.6k. With 60μA on NTC pin, the voltage
is only (15.6k*60μA) = 0.937V. This value is much lower than
the threshold voltage of 1.20V. Therefore, a resistor is
needed to be in series with the NTC. The required resistance
can be calculated by:
---------------- – 15.6k Ω = 4.4k Ω
54μA
6μA
SW1
VR_TT#
1.20V
60 μ A
(EQ. 7)
+
V NTC
-
NTC
R NTC
-
+
4.42k is a standard resistor value. Therefore, the NTC
branch should have a 470k NTC and 4.42k resistor in series.
The part number for the NTC thermistor is ERTJ0EV474J. It
is a 0402 package. NTC thermistor will be placed in the hot
R s
1.24V
SW2
spot of the board.
1.20V
INTERNAL TO
ISL6260C
FIGURE 45. CIRCUITRY ASSOCIATED WITH THE THERMAL
THROTTLING FEATURE OF THE ISL6260C
When temperature increases, the NTC thermistor resistance
on NTC pin decreases. The voltage on NTC pin decreases
to a level lower than 1.20V. The comparator changes polarity
and turns SW1 off and throws SW2 to 1.24V. This pulls
VR_TT# low and sends the signal to start thermal throttle.
There is a 6μA current reduction on NTC pin and 40mV
voltage increase on threshold voltage of the comparator in
this state. The VR_TT# signal will be used to change the
22
FN9259.3
June 21, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6262AIRZ | IC CORE CTRLR 2PHASE 48-QFN |
| ISL6262IRZ | IC CORE CTRLR 2PHASE 48-QFN |
| ISL6263AIRZ | IC PWN CTRLR SYNC BUCK 32QFN |
| ISL6263BHRZ | IC DC/DC BUCK CTRLR 1PH 32-QFN |
| ISL6263CHRZ-T | IC VOLT REG 1PH 5BIT VID 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6260CCRZ-T | 功能描述:电流型 PWM 控制器 MULTI-PHS(3 PHS EXT DC/DC BUCK CONT RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6260CIRZ | 功能描述:电流型 PWM 控制器 MULTI-PHS(3 PHS EXT DC/DC BUCK CONT RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6260CIRZ-T | 功能描述:电流型 PWM 控制器 MULTI-PHS(3 PHS EXT DC/DC BUCK CONT RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6260CRZ | 功能描述:直流/直流开关调节器 MULTI-PHS3 PHS EXT DC/DC BUCK CNTRLR RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6260CRZR5242 | 制造商:Intersil Corporation 功能描述:53289C01 MASK ONLY WITH DOT ON BRAND - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。