参数资料
| 型号： | ISL6322IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 23/41页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 4PHASE BUCK 48-QFN |
| 标准包装： | 4,000 |
| 应用： | 控制器，Intel VR10、VR11、AMD CPU |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.99 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
ISL6322
1.6
ISL6322 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
1.4
VCC
1.2
PVCC1
1.0
+ 12 V
0.8
0.6
0.4
Q GATE = 100nC
POR
CIRCUIT
ENABLE
COMPARATOR
+
EN
10.7k Ω
0.2
20nC
50nC
-
1.40k Ω
0.0
0.85V
0.0
0.1
0.2
0.3
0.4 0.5 0.6
0.7
0.8
0.9
1.0
Δ V BOOT_CAP (V)
+
EN_PH4
FIGURE 9. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
Gate Drive Voltage Versatility
SOFT-START
AND
FAULT LOGIC
-
1.21V
The ISL6322 provides the user flexibility in choosing the
gate drive voltage for efficiency optimization. The controller
ties the upper and lower drive rails together. Simply applying
a voltage from 5V up to 12V on PVCC sets both gate drive
rail voltages simultaneously.
Initialization
Prior to initialization, proper conditions must exist on the EN,
VCC, PVCC and the VID pins. When the conditions are met,
the controller begins soft-start. Once the output voltage is
within the proper window of operation, the controller asserts
PGOOD.
Enable and Disable
While in shutdown mode, the PWM outputs are held in a
high-impedance state to assure the drivers remain off. The
following input conditions must be met, for both Intel and
AMD modes of operation, before the ISL6322 is released
from shutdown mode to begin the soft-start startup
sequence:
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6322 is guaranteed. Hysteresis between the rising
and falling thresholds assure that once enabled, the
ISL6322 will not inadvertently turn off unless the bias
voltage drops substantially (see “Electrical
Specifications” on page 7).
2. The voltage on EN must be above 0.85V. The EN input
allows for power sequencing between the controller bias
voltage and another voltage rail. The enable comparator
holds the ISL6322 in shutdown until the voltage at EN
rises above 0.85V. The enable comparator has 110mV of
hysteresis to prevent bounce.
23
FIGURE 10. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
3. The voltage on the EN_PH4 pin must be above 1.21V.
The EN_PH4 input allows for power sequencing between
the controller and the external driver.
4. The driver bias voltage applied at the PVCC pins must
reach the internal power-on reset (POR) rising threshold.
In order for the ISL6322 to begin operation, PVCC1 is the
only pin that is required to have a voltage applied that
exceeds POR. However, for 2 or 3-phase operation
PVCC2 and PVCC3 must also exceed the POR
threshold. Hysteresis between the rising and falling
thresholds assure that once enabled, the ISL6322 will not
inadvertently turn off unless the PVCC bias voltage drops
substantially (see “Electrical Specifications” on page 7).
For Intel VR10, VR11 and AMD 6-bit modes of operation
these are the only conditions that must be met for the
controller to immediately begin the soft-start sequence. If
running in AMD 5-bit mode of operation there is one more
condition that must be met:
5. The VID code must not be 11111 in AMD 5-bit mode. This
code signals the controller that no load is present. The
controller will not allow soft-start to begin if this VID code
is present on the VID pins.
Once all of these conditions are met the controller will begin
the soft-start sequence and will ramp the output voltage up
to the user designated level.
Intel Soft-Start
The soft-start function allows the converter to bring up the
output voltage in a controlled fashion, resulting in a linear
ramp-up. The soft-start sequence for the Intel modes of
operation is slightly different then the AMD soft-start
sequence.
FN6328.2
August 2, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ASM08DTBS | CONN EDGECARD 16POS R/A .156 SLD |
| AYM12DTMN-S664 | CONN EDGECARD 24POS R/A .156 |
| ECC50DREF-S734 | CONN EDGECARD 100POS .100 EYELET |
| 63USC12000MEFCSN35X45 | CAP ALUM 12000UF 63V 20% SNAP-IN |
| 0925-332K | COIL RF 3.3UH MOLDED SHIELDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6323ACRZ | 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323ACRZR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONT. FOR CORE+NORTHBRIDGE,1 PHASE PSI, 3.4MHZ SVI - Rail/Tube 制造商:Intersil Corporation 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323ACRZ-T | 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323ACRZ-TR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONTROLLER, CORE+NORTHBRIDGE,1 PHASE PSI,3.4MHZ SV - Tape and Reel 制造商:Intersil Corporation 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6323ACRZ-T WITH GOLD BOND WIRE ONLY, T&R - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。