参数资料
| 型号： | ISL6323ACRZ |
| 厂商： | Intersil |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC PWM CTRLR SYNC BUCK DL 48QFN |
| 标准包装： | 43 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 最高 2V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ISL6323A
ISL6323A INTERNAL CIRCUIT
EXTERNAL CIRCUIT
VCC
PVCC1_2
If the controller is configured for 2-phase CORE operation,
then the resistor divider can be used for sequencing the
controller with another voltage rail. The resistor divider to EN
should be selected using a similar approach as the previous
driver discussion.
PVCC_NB
+ 12 V
The EN pin is also used to force the ISL6323A into either
PVI or SVI mode. The mode is set upon the rising edge of
POR
CIRCUIT
ENABLE
COMPARATOR
+
-
0.86V
EN
10.7k Ω
1.00k Ω
the EN signal. When the voltage on the EN pin rises above
0.86V, the mode will be set depending upon the status of the
VID1/SEL pin.
Phase Detection
The ISEN3- and ISEN4- pins are monitored prior to soft-start
to determine the number of active CORE channel phases.
If ISEN4- is tied to VCC, the controller will configure the
channel firing order and timing for 3-phase operation. If
ISEN3-
ISEN3- and ISEN4- are tied to VCC, the controller will set
SOFT-START
AND
CHANNEL
DETECT
ISEN4-
the channel firing order and timing for 2-phase operation
(see “PWM Operation” on page 14 for details).
V DAC
3.25 × 10
FAULT LOGIC
FIGURE 12. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
turn off unless the bias voltage drops substantially (see
Electrical Specifications on page 9).
The bias voltage applied to the PVCC1_2 and PVCC_NB
pins power the internal MOSFET drivers of each output
channel. In order for the ISL6323A to begin operation, both
PVCC inputs must exceed their POR rising threshold to
guarantee proper operation of the internal drivers.
Hysteresis between the rising and falling thresholds assure
that once enabled, the ISL6323A will not inadvertently turn
off unless the PVCC bias voltage drops substantially (see
“Electrical Specifications” on page 9). Depending on the
number of active CORE channels determined by the Phase
Detect block, the external driver POR checking is supported
by the Enable Comparator.
Enable Comparator
The ISL6323A features a dual function enable input (EN) for
enabling the controller and power sequencing between the
controller and external drivers or another voltage rail. The
enable comparator holds the ISL6323A in shutdown until the
voltage at EN rises above 0.86V. The enable comparator has
about 110mV of hysteresis to prevent bounce. It is important
that the driver ICs reach their rising POR level before the
ISL6323A becomes enabled. The schematic in Figure 12
demonstrates sequencing the ISL6323A with the ISL66xx
family of Intersil MOSFET drivers, which require 12V bias.
When selecting the value of the resistor divider the driver
maximum rising POR threshold should be used for
calculating the proper resistor values. This will prevent
improper sequencing events from creating false trips during
soft-start.
22
Soft-Start Output Voltage Targets
Once the POR and Phase Detect blocks and enable
comparator are satisfied, the controller will begin the soft-
start sequence and will ramp the CORE and NB output
voltages up to the SVI interface designated target level if the
controller is set SVI mode. If set to PVI mode, the North
Bridge regulator is disabled and the core is soft started to the
level designated by the parallel VID code.
SVI Mode
Prior to soft-starting both CORE and NB outputs, the
ISL6323A must check the state of the SVI interface inputs to
determine the correct target voltages for both outputs. When
the controller is enabled, the state of the VFIXEN, SVD and
SVC inputs are checked and the target output voltages set
for both CORE and NB outputs are set by the DAC (see
only change if the EN signal is pulled low or after a POR
reset of VCC.
Soft-Start
The soft-start sequence is composed of three periods, as
shown in Figure 13. At the beginning of soft-start, the DAC
immediately obtains the output voltage targets for both
outputs by decoding the state of the SVI or PVI inputs. A
100μs fixed delay time, TDA, proceeds the output voltage
rise. After this delay period the ISL6323A will begin ramping
both CORE and NB output voltages to the programmed DAC
level at a fixed rate of 3.25mV/μs. The amount of time
required to ramp the output voltage to the final DAC voltage
is referred to as TDB, and can be calculated as shown in
Equation 19.
TDB = ------------------------------ (EQ. 19)
– 3
FN6878.1
May 12, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| LD6806CX4/25H,315 | IC REG LDO 2.5V .2A 4WLCSP |
| 420USC390MEFCSN30X40 | CAP ALUM 390UF 420V 20% SNAP-IN |
| 2256-19L | POWER CHOKE 33UH MOLDED AXIAL |
| ISL6422BEVEZ-T | IC VREG DUAL LNB W/I2C 38EPTSSOP |
| 160MXG1500MEFCSN30X35 | CAP ALUM 1500UF 160V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6323ACRZR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONT. FOR CORE+NORTHBRIDGE,1 PHASE PSI, 3.4MHZ SVI - Rail/Tube 制造商:Intersil Corporation 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323ACRZ-T | 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323ACRZ-TR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONTROLLER, CORE+NORTHBRIDGE,1 PHASE PSI,3.4MHZ SV - Tape and Reel 制造商:Intersil Corporation 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6323ACRZ-T WITH GOLD BOND WIRE ONLY, T&R - Tape and Reel |
| ISL6323AIRZ | 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。