- 您现在的位置：买卖IC网 > PDF目录15161 > ISL6326CRZ (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL6326CRZ |
| 厂商： | Intersil |
| 文件页数： | 26/30页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 50 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 275kHz |
| 占空比： | 25% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页
ISL6326
------------------- > f 0
R C = R FB ------------------------------------
0.75V
2 π V PP R FB f 0
------------------- ≤ f 0 < ------------------------------
COMPENSATING LOAD-LINE REGULATED
CONVERTER
The load-line regulated converter behaves in a similar
manner to a peak-current mode controller because the two
poles at the output-filter L-C resonant frequency split with
the introduction of current information into the control loop.
The final location of these poles is determined by the system
function, the gain of the current signal, and the value of the
compensation components, R C and C C .
Case 1:
Case 2:
1
2 π LC
2 π f 0 V pp LC
IN
0.75V IN
C C = ------------------------------------
1 1
2 π LC 2 π C ( ESR )
R C = R FB --------------------------------------------
0.75 V
C C = -------------------------------------------------------------
PP R FB LC
( 2 π ) 2 f 2 V
Since the system poles and zero are affected by the values
of the components that are meant to compensate them, the
solution to the system equation becomes fairly complicated.
Fortunately, there is a simple approximation that comes very
close to an optimal solution. Treating the system as though it
were a voltage-mode regulator by compensating the L-C
poles and the ESR zero of the voltage-mode approximation
V PP ( 2 π ) 2 f 02 LC
IN
0.75V IN
0
(EQ. 35)
f 0 > ------------------------------
0.75 V IN ( ESR )
yields a solution that is always stable with very close to ideal
transient performance.
C 2 (OPTIONAL)
Case 3:
1
2 π C ( ESR )
2 π f 0 V pp L
R C = R FB ------------------------------------------
2 π V PP R FB f 0 L
R C
C C
COMP
0.75V IN ( ESR ) C
C C = -------------------------------------------------
In Equation 35, L is the per-channel filter inductance divided
FB
by the number of active channels; C is the sum total of all
output capacitors; ESR is the equivalent-series resistance of
R FB
+
V DROOP
IDROOP
the bulk output-filter capacitance; and V P-P is the sawtooth
-
VDIFF
FIGURE 16. COMPENSATION CONFIGURATION FOR
LOAD-LINE REGULATED ISL6326 CIRCUIT
The feedback resistor, R FB , has already been chosen as
outlined in “Load-Line Regulation Resistor” on page 25.
Select a target bandwidth for the compensated system, f 0 .
The target bandwidth must be large enough to assure
adequate transient performance, but smaller than 1/3 of the
per-channel switching frequency. The values of the
compensation components depend on the relationships of f 0
to the L-C pole frequency and the ESR zero frequency. For
each of the three cases which follow, there is a separate set
of equations for the compensation components.
26
The optional capacitor C 2 , is sometimes needed to bypass
noise away from the PWM comparator (see Figure 16). Keep
a position available for C 2 , and be prepared to install a
high-frequency capacitor of between 22pF and 150pF in
case any leading-edge jitter problem is noted.
Once selected, the compensation values in Equation 35
assure a stable converter with reasonable transient
performance. In most cases, transient performance can be
improved by making adjustments to R C . Slowly increase the
value of R C while observing the transient performance on an
oscilloscope until no further improvement is noted. Normally,
C C will not need adjustment. Keep the value of C C from
Equation 35 unless some performance issue is noted.
COMPENSATION WITHOUT LOAD-LINE REGULATION
The non load-line regulated converter is accurately modeled
as a voltage-mode regulator with two poles at the L-C
resonant frequency and a zero at the ESR frequency. A
type-III controller, as shown in Figure 17, provides the
necessary compensation.
FN9262.1
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| EBM12DRMN-S273 | CONN EDGECARD 24POS .156 WW |
| EBM12DRMD-S273 | CONN EDGECARD 24POS .156 WW |
| ISL8126CRZ | IC REG CTRLR BUCK PWM VM 32-QFN |
| GEM43DSES-S243 | CONN EDGECARD 86POS .156 EYELET |
| UPJ1A682MHD6 | CAP ALUM 6800UF 10V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6326CRZ-T | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR COM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326CRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6326CRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6326IRZ | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR IND RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326IRZ-T | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR IND RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6327ACRZ | 功能描述:IC REG CTRLR BUCK PWM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。