参数资料
| 型号： | ISL6425ER-T |
| 厂商： | Intersil |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC REG DUAL LNBP TTL-INP 32-QFN |
| 标准包装： | 6,000 |
| 应用： | 转换器，卫星信号接收机顶盒设计 |
| 输入电压： | 8 V ~ 14 V |
| 输出数： | 2 |
| 输出电压： | 13 V ~ 18 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 带卷 (TR) |
ISL6425
Functional Pin Description
SYMBOL
SDA
SCL
VSW
PGND
CS
SGND
AGND
TCAP
BYPASS
DSQIN
VCC
GATE
VOUT
ADDR
COMP
FB
FUNCTION
Bidirectional data from/to I 2 C bus.
Clock from I 2 C bus.
Input of the linear post-regulator.
Dedicated ground for the output gate driver of the PWM.
Current sense input; connect Rsc at this pin for desired overcurrent value for the PWM.
Small signal ground for the IC.
Analog ground for the IC.
Capacitor for setting rise and fall time of the output of the LNB. Use a capacitor value of 1μF or higher.
Bypass capacitor for internal 5V.
When HIGH this pin enables the internal 22kHz modulation for the LNB, Use this pin for tone enable function for
the LNB.
Main power supply to the chip.
This is the device output of the PWM. This high current driver output is capable of driving the gate of a power FET.
This output is actively held low when Vcc is below the UVLO threshold.
Output voltage for the LNB.
Address pin to select two different addresses per voltage level at this pin.
Error amp output used for compensation.
Feedback pin for the PWM.
CPVOUT, CPSWIN, CPSWOUT Charge pump connections.
SEL18V
When connected HIGH, this pin will change the output of the PWM to 18V.
Functional Description
The ISL6425 single output voltage regulator makes an ideal
choice for advanced satellite set-top box and personal video
recorder applications. Both supply and control voltage
outputs for a low noise block (LNB) are available
simultaneously in any output configuration. The device
utilizes a built-in DC/DC step-converter that, from a single
supply source ranging from 8V to 14V, generates the voltage
that enables the linear post-regulator to work with a
minimum of dissipated power. An undervoltage lockout
circuit disables the circuit when V CC drops below a fixed
threshold (7.5V typ).
DiSEqC Encoding
The internal oscillator is factory-trimmed to provide a tone of
22kHz in accordance with DISeqC standards. No further
adjustment is required. The 22kHz oscillator can be
controlled either by the I 2 C interface (ENT bit) or by a
dedicated pin (DSQIN) that allows immediate DiSEqC data
encoding for the LNB. All the functions of this IC are
controlled via the I 2 C bus by writing to the system registers
(SR). The same registers can be read back, and two bits will
report the diagnostic status. The internal oscillator operates
the converters at ten times the tone frequency. The device
offers full I 2 C compatible functionality, 3.3V or 5V, and up to
400kHz operation.
If the Tone Enable (ENT) bit is set LOW through I 2 C, then
the DSQIN terminal activates the internal tone signal,
7
modulating the dc output with a 0.3V, 22kHz, symmetrical
waveform. The presence of this signal usually gives the LNB
information about the band to be received.
Burst coding of the 22kHz tone can be accomplished due to
the fast response of the DSQIN input and rapid tone
response. This allows implementation of the DiSEqC
(EUTELSAT) protocols.
When the ENT bit is set HIGH, a continuous 22kHz tone is
generated regardless of the DSQIN pin logic status. The
ENT bit must be set LOW when the DSQIN pin is used for
DiSEqC encoding.
Linear Regulator
The output linear regulator will sink and source current. This
feature allows full modulation capability into capacitive loads
as high as 0.25 μ F. In order to minimize the power
dissipation, the output voltage of the internal step-up
converter is adjusted to allow the linear regulator to work at
minimum dropout.
When the device is put in the shutdown mode (EN = LOW),
the PWM power block is disabled. When the regulator block
is active (EN = HIGH), the output can be logic controlled to
be 13V or 18V (typical) by means of the VSEL bit (Voltage
Select) for remote controlling of non-DiSEqC LNBs.
Additionally, it is possible to increment by 1V (typical) the
selected voltage value to compensate for the excess voltage
drop along the coaxial cable (LLC bit HIGH).
FN9176.1
February 8, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6431CB-T | IC REG CTRLR BUCK PWM VM 8-SOIC |
| ISL6439CB | IC REG CTRLR BUCK PWM VM 14-SOIC |
| ISL6440IA-TK | IC REG CTRLR BUCK PWM CM 24-QSOP |
| ISL6441IR-TK | IC CTRLR PWM DUAL 1.4MHZ 28-QFN |
| ISL6443AIVZ | IC CTRLR SGL/STP DWN PWM 28TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6425ERZ | 功能描述:电流型 PWM 控制器 SINGLE LNBP SUPPLY CONTROL VG W/TTL INP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6425ERZ-T | 功能描述:电流型 PWM 控制器 SINGLE LNBP SUPPLY CONTROL VG W/TTL INP RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6425EVAL2 | 功能描述:EVAL BOARD 2 FOR ISL6425 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:* 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL6426CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ISL6426CR | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。