参数资料
| 型号： | ISL6431CB-T |
| 厂商： | Intersil |
| 文件页数： | 4/10页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 8-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 340kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
ISL6431
Electrical Specifications
Recommended Operating Conditions, Unless Otherwise Noted V CC = 5.0V ± 5% and T A = 25 o C (Continued)
PARAMETER
Lower Gate Sink Current
SYMBOL
I LGATE-SNK
ISL6431CB
ISL6431IB
TEST CONDITIONS
MIN
-
-
TYP
2.0
2.0
MAX
-
-
UNITS
A
A
PROTECTION / DISABLE
OCSET Current Source
Disable Threshold
I OCSET
V DISABLE
ISL6431CB
ISL6431IB
ISL6431CB
ISL6431IB
17
14
-
-
20
20
-
-
22
24
0.8
0.8
μ A
μ A
V
V
r DS ( ON )
I PEAK = ----------------------
Functional Pin Descriptions
VCC (Pin 5)
This is the main bias supply for the ISL6431, as well as the
lower MOSFET’s gate. Connect a well-decoupled 5V supply
to this pin.
FB (Pin 6)
This pin is the inverting input of the internal error amplifier.
Use this pin, in combination with the COMP/OCSET pin, to
compensate the voltage-control feedback loop of the
converter.
GND (Pin 3)
This pin represents the signal and power ground for the IC.
Tie this pin to the ground island/plane through the lowest
impedance connection available.
PHASE (Pin 8)
Connect this pin to the upper MOSFET source. This pin is
used to monitor the voltage drop across the upper MOSFET
for overcurrent protection. This pin is also monitored by the
continuously adaptive shoot-through protection circuitry to
determine when the upper MOSFET has turned off.
UGATE (Pin 2)
Connect this pin to the upper MOSFET’s gate. This pin
provides the PWM-controlled gate drive for the upper
MOSFET. This pin is also monitored by the adaptive shoot-
through protection circuitry to determine when the upper
MOSFET has turned off. Do not insert any circuitry between
this pin and the gate of the upper MOSFET, as it may
interfere with the internal adaptive shoot-through protection
circuitry and render it ineffective.
BOOT (Pin 1)
This pin provides ground referenced bias voltage to the
upper MOSFET driver. A bootstrap circuit is used to create a
voltage suitable to drive a logic-level N-channel MOSFET.
COMP/OCSET (Pin 7)
This is a multiplexed pin. During a short period of time
following power-on reset (POR), this pin is used to determine
the overcurrent threshold of the converter. Connect a
resistor (R OCSET ) from this pin to the drain of the upper
MOSFET (V CC ). R OCSET , an internal 20 μ A current source
4
(I OCSET ), and the upper MOSFET on-resistance (r DS(ON) )
set the converter overcurrent (OC) trip point according to the
following equation:
I OCSET xR OC SET
I PEAK = -------------------------------------------------
Internal circuitry of the ISL6431 will not recognize a voltage
drop across R OCSET larger than 0.5V. Any voltage drop
across R OCSET that is greater than 0.5V will set the
overcurrent trip point to:
0.5V
r DS ( ON )
An overcurrent trip cycles the soft-start function.
Pulling OCSET to a level below 0.8V will disable the
controller. Disabling the ISL6431 causes the oscillator to
stop, the LGATE and UGATE outputs to be held low, and the
softstart circuitry to re-arm.
During soft-start, and all the time during normal converter
operation, this pin represents the output of the error
amplifier. Use this pin, in combination with the FB pin, to
compensate the voltage-control feedback loop of the
converter.
LGATE (Pin 4)
Connect this pin to the lower MOSFET’s gate. This pin
provides the PWM-controlled gate drive for the lower
MOSFET. This pin is also monitored by the adaptive shoot-
through protection circuitry to determine when the lower
MOSFET has turned off. Do not insert any circuitry between
this pin and the gate of the lower MOSFET, as it may
interfere with the internal adaptive shoot-through protection
circuitry and render it ineffective.
Functional Descriptions
Initialization
The ISL6431 automatically initializes upon receipt of power.
The Power-On Reset (POR) function continually monitors the
bias voltage at the VCC pin. The POR function initiates the
Overcurrent Protection (OCP) sampling and hold operation
after the supply voltage exceeds its POR threshold. Upon
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6439CB | IC REG CTRLR BUCK PWM VM 14-SOIC |
| ISL6440IA-TK | IC REG CTRLR BUCK PWM CM 24-QSOP |
| ISL6441IR-TK | IC CTRLR PWM DUAL 1.4MHZ 28-QFN |
| ISL6443AIVZ | IC CTRLR SGL/STP DWN PWM 28TSSOP |
| ISL6443IR-TK | IC CTRLR PWM DUAL 300KHZ 28-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6431IB | 制造商:Intersil Corporation 功能描述: |
| ISL6432CB | 制造商:Intersil Corporation 功能描述: |
| ISL6432CB-T | 功能描述:IC REG QD BCK/LINEAR 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6433BCB | 制造商:Intersil Corporation 功能描述: |
| ISL6434CB | 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。