参数资料
| 型号： | ISL6444CAZ-T |
| 厂商： | Intersil |
| 文件页数： | 11/19页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR 28-QSOP |
| 标准包装： | 2,500 |
| 应用： | 控制器，DDR |
| 输入电压： | 4.5 V ~ 24 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -10°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 带卷 (TR) |
ISL6444
Gate Control Logic
The gate control logic translates generated PWM signals
into gate drive signals providing necessary amplification,
level shift, and shoot-trough protection. Also, it bears some
functions that help to optimize the IC performance over a
wide range of the operational conditions. As MOSFET
switching time can very dramatically from type to type and
with the input voltage, the gate control logic provides
adaptive dead time by monitoring real gate waveforms of
both the upper and the lower MOSFETs.
Dual-Step Conversion
The ISL6444 dual channel controller can be used either in
power systems with a single-stage power conversion when
the battery power is converted into the desired output
If the lower MOSFET current exceeds the overcurrent
threshold, a pulse skipping circuit is activated. The upper
MOSFET will not be turned on as long as the sensed
current is higher then the threshold value. This limits the
current supplied by the DC voltage source. This condition
keeps on for eight clock cycles after the overcurrent
comparator was tripped for the first time. If after these first
eight clock cycles, the current exceeds the overcurrent
threshold again in a time interval of another eight clock
cycles, the overcurrent protection latches and disables the
chip. If the overcurrent condition goes away during the first
eight clock cycles, normal operation is restored and the
overcurrent circuit resets itself sixteen clock cycles after the
overcurrent threshold was exceeded the first time, Figure 6.
voltage in one step, or in the systems where some
intermediate voltages are initially established. The choice of
the approach may be dictated by the overall system design
1
IL
PGOO D
8 CLK
SHUTDOWN
I OC ? R
criteria or simply to be a matter of voltages available to the
system designer, like in the case of PCI card applications.
When the power input voltage is a regulated 5V or 3.3V
system bus, the feed-forward ramp may become too
shallow, which creates the possibility of duty-factor jitter
especially in a noisy environment. The noise susceptibility
when operating from low level regulated power sources can
be improved by connecting the VIN pin to ground via a
resistor. The internal pull-up current source of ~15 μ A will
create a voltage drop across the resistor. If this voltage is
lower than 2.5V, the feed-forward ramp generator will be
internally reconnected from the VIN pin to the VCC pin and
the ramp slew rate will be doubled. Application circuits for
dual-step power conversion are presented in Figure 10.
Protections
The converter output is monitored and protected against
extreme overload, short circuit, overvoltage, and
undervoltage conditions.
A sustained overload on the output sets the PGOOD low and
latches-off the whole chip. The controller operation can be
restored by cycling the VCC voltage or an enable (EN) pin.
Overcurrent Protection
Both PWM controllers use the lower MOSFET’s
on-resistance -- r DS(ON) to monitor the current for
protection against shorted outputs. The sensed current
from the ISEN pin is compared with a current set by a
resistor connected from the OCSET pin to ground.
11.2V ? ( R CS + 100 Ω )
R OCSET = ------------------------------------------------------------
DS ( ON )
Where, I OC is a desired overcurrent protection threshold and
R CS is the value of the current sense resistor connected to
the I SEN pin.
11
2
VOUT
3
Ch1 5.0V Ch2 100mV M 10.0 μ s
Ch3 1.0A Ω
FIGURE 6. OVERCURRENT PROTECTION WAVEFORMS
If load step is strong enough to pull output voltage lower
than the undervoltage threshold, the chip shuts down
immediately.
Because of the nature of the used current sensing
technique, and to accommodate wide range of the r DS(ON)
variation, the value of the overcurrent threshold should
represent overload current about 150%...180% of the
nominal value. If accurate current protection is desired, a
current sense resistor placed in series with the lower
MOSFET source may be used.
Overvoltage Protection
Should the output voltage increase over 115% of the normal
value due to the upper MOSFET failure, or other reasons,
the overvoltage protection comparator will force the
synchronous rectifier gate driver high. This action actively
pulls down the output voltage and eventually attempts to
blow the battery fuse. As soon as the output voltage drops
below the threshold, the OVP comparator is disengaged.
This OVP scheme provides a ‘soft’ crowbar function which
helps to tackle severe load transients and does not invert the
output voltage when activated -- a common problem for OVP
schemes with a latch.
FN9069.3
April 12, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HBC13DRXH-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| 450USG270MEFCSN22X50 | CAP ALUM 270UF 450V 20% SNAP-IN |
| GCB92DHHN-S378 | CONN EDGECARD 184POS 5V .050 SLD |
| HMC13DRXI-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| GCB92DHHD-S378 | CONN EDGECARD 184POS 5V .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6445EVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6445 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6445IAZ | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6445IAZS2695 | 制造商:Intersil Corporation 功能描述: |
| ISL6445IAZ-TK | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6445IAZ-TKS2645 | 制造商:Intersil Corporation 功能描述:DC DC CNTRLR DUAL-OUT STEP DOWN 4.5V TO 24V 24QSOP W - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。