参数资料
| 型号： | ISL6444CAZ-T |
| 厂商： | Intersil |
| 文件页数： | 7/19页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR 28-QSOP |
| 标准包装： | 2,500 |
| 应用： | 控制器，DDR |
| 输入电压： | 4.5 V ~ 24 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -10°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 带卷 (TR) |
ISL6444
Functional Pin Description
GND (Pin 1)
Signal ground for the IC.
LGATE1, LGATE2 (Pin 2, 27)
These are outputs of the lower MOSFET drivers.
PGND1, PGND2 (Pin 3, 26)
These pins provide the return connection for lower gate
drivers. These pins are connected to sources of the lower
MOSFETs of their respective converters.
PHASE1, PHASE2 (Pin 4, 25)
The PHASE1 and PHASE2 points are the junction points of
the upper MOSFET sources, output filter inductors, and
lower MOSFET drains. Connect these pins to the respective
converter ’s upper MOSFET source.
UGATE1, UGATE2 (Pin 5, 24)
These pins provide the gate drive for the upper MOSFETs.
BOOT1, BOOT2 (Pin 6, 23)
These pins power the upper MOSFET drivers of the PWM
converter. Connect this pin to the junction of the bootstrap
capacitor with the cathode of the bootstrap diode. Anode of
the bootstrap diode is connected to the VCC pin.
ISEN1, ISEN2 (Pin 7, 22)
These pins are used to monitor the voltage drop across the
lower MOSFET for current feedback and overcurrent
protection. For precise current detection these inputs can be
connected to the optional current sense resistors placed in
series with the source of the lower MOSFETs.
EN1, EN2 (Pin 8, 21)
These pins enable operation of the respective converter
when high. When both pins are low, the chip is disabled and
only low leakage current <1μA is taken from VCC and VIN.
VOUT1, VOUT2 (Pin 9, 20)
These pins when connected to the converters’ respective
outputs provide the output voltage inside the chip to reduce
output voltage excursion during HYS/PWM transition. When
connected to ground, the se pins command forced
converters operate in continuous conduction mode at all
load levels.
VSEN1, VSEN2 (Pin 10, 19)
These pins are connected to the resistive dividers that set
the desired output voltage. The PGOOD, UVP, and OVP
circuits use this signal to report output voltage status.
OCSET1 (Pin 11)
A resistor from this pin to ground sets the over current
threshold for the first controller.
7
SOFT1, SOFT2 (Pin 12, 17)
These pins provide soft-start function for their respective
controllers. When the chip is enabled, the regulated 5 μ A
pull-up current source charges the capacitor connected from
the pin to ground. The output voltage of the converter follows
the ramping voltage on the SOFT pin.
DDR (Pin 13)
This pin, when high, transforms dual channel chip into
complete DDR memory solution. The OCSET2 pin becomes
an input to provide the required tracking function. The
channel synchronization is changed from out-of-phase to
in-phase. The PG2/REF pin becomes the output of the
VDDQ/2 buffered voltage that is used as a reference voltage
by the second channel.
VIN (Pin 14)
Provides battery voltage to the oscillator for feed-forward
rejection of the input voltage variation.
When connected to ground via 100k Ω resistor while the
DDR pin is high, this pin commands the out-of-phase 90 o
channels synchronization for reduces inter-channel
interference.
PG1 (Pin 15)
PGOOD1 is an open drain output used to indicate the status
of the output voltage. This pin is pulled low when the first
channel output is not within ±10% of the set value.
PG2/REF (Pin 16)
This pin has a double function depending on the mode the
chip is operating. When the chip is used as a dual channel
PWM controller (DDR = 0), the pin provides a PGOOD2
function for the second channel. The pin is pulled low when
the second channel output is not within ±10% of the set value.
In DDR mode (DDR = 1), this pin serves as an output of the
buffer amplifier that provides VDDQ/2 reference voltage
applied to the OCSET2 pin.
OCSET2 (Pin 18)
In a dual channel application (DDR = 0), a resistor from this
pin to ground sets the over current threshold for the second
controller.
In the DDR application (DDR = 1), this pin sets the output
voltage of the buffer amplifier and the second controller and
should be connected to the center point of a divider from the
VDDQ output.
VCC (Pin 28)
This pin powers the controller.
FN9069.3
April 12, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HBC13DRXH-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| 450USG270MEFCSN22X50 | CAP ALUM 270UF 450V 20% SNAP-IN |
| GCB92DHHN-S378 | CONN EDGECARD 184POS 5V .050 SLD |
| HMC13DRXI-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| GCB92DHHD-S378 | CONN EDGECARD 184POS 5V .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6445EVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6445 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6445IAZ | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6445IAZS2695 | 制造商:Intersil Corporation 功能描述: |
| ISL6445IAZ-TK | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6445IAZ-TKS2645 | 制造商:Intersil Corporation 功能描述:DC DC CNTRLR DUAL-OUT STEP DOWN 4.5V TO 24V 24QSOP W - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。