- 您现在的位置：买卖IC网 > PDF目录15064 > ISL6526AIB-T (Intersil)IC REG CTRLR BUCK PWM VM 14-SOIC PDF资料下载
参数资料
| 型号： | ISL6526AIB-T |
| 厂商： | Intersil |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 14-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 650kHz |
| 占空比： | 100% |
| 电源电压： | 2.97 V ~ 3.63 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
ISL6526, ISL6526A
ENABLE
This pin is the open-collector enable pin. Pulling this pin to a
level below 0.8V will disable the controller. Disabling the
ISL6526, ISL6526A causes the oscillator to stop, the LGATE
and UGATE outputs to be held low, and the soft-start
circuitry to re-arm.
CT1 and CT2
These pins are the connections for the external charge
pump capacitor. A minimum of a 0.1μF ceramic capacitor is
recommended for proper operation of the IC.
CPVOUT
0V
(1V/DIV)
CPVOUT (5V)
VCC (3.3V)
V OUT (2.50V)
This pin represents the output of the charge pump. The
voltage at this pin is the bias voltage for the IC. Connect a
t0
t1
t2
t3
TIME
decoupling capacitor from this pin to ground. The value of the
decoupling capacitor should be at least 10x the value of the
charge pump capacitor. This pin may be tied to the bootstrap
circuit as the source for creating the BOOT voltage.
CPGND
This pin represents the signal and power ground for the
charge pump. Tie this pin to the ground island/plane through
the lowest impedance connection available.
Functional Description
Initialization
The ISL6526, ISL6526A automatically initialize upon receipt
of power. Special sequencing of the input supplies is not
necessary. The Power-On Reset (POR) function continually
monitors the output voltage of the charge pump. During
POR, the charge pump operates on a free running oscillator.
Once the POR level is reached, the charge pump oscillator
is synched to the PWM oscillator. The POR function also
initiates the soft-start operation after the charge pump output
voltage exceeds its POR threshold.
Soft-Start
The POR function initiates the digital soft-start sequence.
The PWM error amplifier reference is clamped to a level
proportional to the soft-start voltage. As the soft-start voltage
slews up, the PWM comparator generates PHASE pulses of
increasing width that charge the output capacitor(s). This
method provides a rapid and controlled output voltage rise.
The soft-start sequence typically takes about 6.5ms.
Figure 1 shows the soft-start sequence for a typical application.
At t0, the +3.3V VCC voltage starts to ramp-up. At time t1, the
Charge Pump begins operation and the +5V CPVOUT IC bias
voltage starts to ramp-up. Once the voltage on CPVOUT
crosses the POR threshold at time t2, the output begins the
FIGURE 1. SOFT-START INTERVAL
Shoot-Through Protection
A shoot-through condition occurs when both the upper
MOSFET and lower MOSFET are turned on simultaneously,
effectively shorting the input voltage to ground. To protect
the regulator from a shoot-through condition, the ISL6526,
ISL6526A incorporate specialized circuitry which insures
that the complementary MOSFETs are not ON
simultaneously.
The adaptive shoot-through protection utilized by the
ISL6526, ISL6526A look at the lower gate drive pin, LGATE,
and the upper gate drive pin, UGATE, to determine whether
a MOSFET is ON or OFF. If the voltage from UGATE or from
LGATE to GND is less than 0.8V, then the respective
MOSFET is defined as being OFF and the complementary
MOSFET is turned ON. This method of shoot-through
protection allows the regulator to sink or source current.
Since the voltage of the lower MOSFET gate and the upper
MOSFET gate are being measured to determine the state of
the MOSFET, the designer is encouraged to consider the
repercussions of introducing external components between
the gate drivers and their respective MOSFET gates before
actually implementing such measures. Doing so may
interfere with the shoot-through protection.
Output Voltage Selection
The output voltage can be programmed to any level between
V IN and the internal reference, 0.8V. An external resistor
divider is used to scale the output voltage relative to the
reference voltage and feed it back to the inverting input of
the error amplifier; see Figure 2. However, since the value of
R1 affects the values of the rest of the compensation
components, it is advisable to keep its value less than 5k Ω .
R4 can be calculated based Equation 2:
R1 × 0.8V
soft-start sequence. The triangle waveform from the PWM
oscillator is compared to the rising error amplifier output
voltage. As the error amplifier voltage increases, the pulse
R4 = --------------------------------------
V OUT1 – 0.8V
(EQ. 2)
width on the UGATE pin increases to reach the steady-state
duty cycle at time t3.
7
If the output voltage desired is 0.8V, simply route the output
back to the FB pin through R1, but do not populate R4.
FN9055.10
November 24, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| X5045M8Z | IC CPU SUPERV 4K EE RST 8-MSOP |
| ISL6526AIB | IC REG CTRLR BUCK PWM VM 14-SOIC |
| X4043M8Z-2.7A | IC CPU SUPERV 4K EEPROM 8-MSOP |
| VI-2WW-EW-F3 | CONVERTER MOD DC/DC 5.5V 100W |
| X4043M8Z-4.5A | IC CPU SUPERV 4K EEPROM 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6526AIR | 功能描述:电压模式 PWM 控制器 Single Synch Buck RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6526AIR-T | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6526AIRZ | 功能描述:电压模式 PWM 控制器 600KHZ SNG PWM W/CHA RGE PUMP 16LD 5X5 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6526AIRZ-T | 功能描述:电压模式 PWM 控制器 600KHZ SINGLE PWM W/CHRG PUMP 16LD 5X5 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6526AIRZ-TK | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。