参数资料
| 型号： | ISL6539CA |
| 厂商： | Intersil |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR DDR DRAM, SDRAM 28QSOP |
| 标准包装： | 48 |
| 应用： | 控制器，DDR DRAM，SDRAM |
| 输入电压： | 3.3 V ~ 18 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 管件 |
ISL6539
drop caused by the AC peak-to-peak current. These two
voltages can be represented by Equations 21 and 22:
Choosing MOSFETs
For a maximum input voltage of 15V, at least a minimum 30V
Δ V c = -----------------
I pp
8Cf sw
(EQ. 21)
MOSFETs should be used. The design has to trade off the
gate charge with the r DS(ON) of the MOSFET:
? For the lower MOSFET, before it is turned on, the body
P lower ( V IN ) ≈ ( 1 – D ( V IN ) ) I load r DS ( ON ) Lower
P uppercond ( V IN ) = D ( V IN ) I load r DS ( ON ) upper
Δ V esr = I P – P ESR (EQ. 22)
These two components constitute a large portion of the total
output voltage ripple. Several capacitors have to be
paralleled in order to reduce the ESR and the voltage ripple.
If the output of the converter has to support another load
with high pulsating current, such as the first channel in
Figure 4, it feeds into the VTT channel which draws high
pulsating current. More capacitors are needed in order to
reduce the equivalent ESR and suppress the voltage ripple
to a tolerable level.
To support a load transient that is faster than the switching
frequency, more capacitors have to be used to reduce the
voltage excursion during load step change. Another aspect
of the capacitor selection is that the total AC current going
through the capacitors has to be less than the rated RMS
current specified on the capacitors, to prevent the capacitor
from overheating.
For DDR applications, as the second channel draws pulsate
current directly from the first channel, it is recommended to
parallel capacitors for output of the first channel to reduce
ESR and smooth ripple. Excessive high ripple voltage at the
output can propagate into the output of the error amplifier
and cause too much phase voltage jitter.
Input Capacitor Selection
The important parameters for the bulk input capacitance are
the voltage rating and the RMS current rating. For reliable
operation, select bulk capacitors with voltage and current
ratings above the maximum input voltage and largest RMS
diode has been conducting. The lower MOSFET driver will
not charge the miller capacitor of this MOSFET.
? In the turning off process of the lower MOSFET, the load
current will shift to the body diode first. The high dv/dt of
the phase node voltage will charge the miller capacitor
through the lower MOSFET driver sinking current path.
This results in much less switching loss of the lower
MOSFETs.
The duty cycle is often very small in high battery voltage
applications, and the lower MOSFET will conduct most of
the switching cycle; therefore, the lower the r DS(ON) of the
lower MOSFET, the less the power loss. The gate charge for
this MOSFET is usually of secondary consideration.
The upper MOSFET does not have this zero voltage
switching condition, and because the upper MOSFET
conducts for less time compared to the lower MOSFET, the
switching loss tends to be dominant. Priority should be given
to the MOSFETs with less gate charge, so that both the gate
driver loss, and switching loss, will be minimized.
For the lower MOSFET, its power loss can be assumed to be
the conduction loss only.
2 (EQ. 24)
For the upper MOSFET, its conduction loss can be written as:
2 (EQ. 25)
and its switching loss can be written as:
P uppersw ( V IN ) = ------------------------------------------ + -------------------------------------------
current required by the circuit. Their voltage rating should be
at least 1.25 times greater than the maximum input voltage,
while a voltage rating of 1.5 times is a conservative
f
V IN I vally t on f sw V IN I peak t off sw
2 2
(EQ. 26)
guideline. For most cases, the RMS current rating
requirement for the input capacitor of a buck regulator is
approximately 1/2 the DC load current.
The maximum RMS current required by the regulator may be
closely approximated through Equation 23:
The peak and valley current of the inductor can be obtained
based on the inductor peak-to-peak current and the load
current. The turn-on and turn-off time can be estimated with
the given gate driver parameters in the “Electrical
Specifications” Table on page 4. For example, if the gate
driver turn-on path MOSFET has a typical ON-resistance of
? ( D – D ) + I
? ------
I
Cin ( RMS )
=
I
OUT
2
2
Ripple ( p – p )
2 D
12
(EQ. 23)
4 Ω , its maximum turn-on current is 1.2A with 5V V CC . This
current would decay as the gate voltage increased. With the
t on = -----------------
In addition to the bulk capacitance, some low ESL ceramic
decoupling is recommended to be used between the drain
terminal of the upper MOSFET and the source terminal of
the lower MOSFET, in order to clamp the parasitic voltage
ringing at the phase node in switching.
16
assumption of linear current decay, the turn-on time of the
MOSFETs can be written as Equation 27:
2Q gd (EQ. 27)
I driver
Q gd is used because when the MOSFET drain-to-source
voltage has fallen to zero, it gets charged. Similarly, the
turn-off time can be estimated based on the gate charge and
the gate drivers sinking current capability.
FN9144.6
April 29, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| X5165S8-2.7T1 | IC SUPERVISOR CPU 16K EE 8-SOIC |
| RMM25DRYI-S13 | CONN EDGECARD 50POS .156 EXTEND |
| ISL6531CR-T | IC CONTROLLER INTEL 32QFN |
| X5165S8-2.7A | IC SUPERVISOR CPU 16K EE 8-SOIC |
| ISL6531CR | IC CONTROLLER INTEL 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6539CA-T | 功能描述:IC CTRLR DDR DRAM, SDRAM 28QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6539CAZ | 功能描述:电流型 PWM 控制器 VER OF ISL6539CA RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6539CAZ-T | 功能描述:电流型 PWM 控制器 VER OF ISL6539CA-T RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6539EVAL1 | 功能描述:EVAL BOARD 1 FOR ISL6539 RoHS:否 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:* 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ISL6539EVAL2 | 功能描述:EVAL BOARD 2 FOR ISL6539 RoHS:否 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:* 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
发布紧急采购，3分钟左右您将得到回复。