参数资料
| 型号： | ISL6556ACR-T |
| 厂商： | Intersil |
| 文件页数： | 9/25页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR MULTIPHASE VRM10 32-QFN |
| 标准包装： | 6,000 |
| 应用： | 控制器，Intel VR10X |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 4 |
| 输出电压： | 0.84 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
ISL6556A
Functional Pin Description
VCC
Supplies all the power necessary to operate the chip. The
controller starts to operate when the voltage on this pin
exceeds the rising POR threshold and shuts down when the
voltage on this pin drops below the falling POR threshold.
Connect this pin directly to a +5V supply or through a series
300 Ω resistor to a +12V supply.
GND
Bias and reference ground for the IC.
EN
This pin is a threshold-sensitive enable input for the
controller. Connecting the 12V supply to EN through an
appropriate resistor divider provides a means to synchronize
power-up of the controller and the MOSFET driver ICs.
When EN is driven above 1.24V, the ISL6556A is active
depending on status of ENLL, the internal POR, and pending
fault states. Driving EN below 1.14V will clear all fault states
and prime the ISL6556 to soft start when re-enabled.
ENLL
This pin is implemented in QFN ISL6556A only. It’s a logic-
level enable input for the controller. When asserted to a logic
high, the ISL6556A is active depending on status of EN, the
internal POR, VID inputs and pending fault states.
Deasserting ENLL will clear all fault states and prime the
ISL6556A to soft start when re-enabled.
FS
A resistor, placed from FS to ground will set the switching
frequency. There is an inverse relationship between the
value of the resistor and the switching frequency. See
Figure 13 and Equation 26.
VID4, VID3, VID2, VID1, VID0, and VID12.5
These are the inputs to the internal DAC that provides the
reference voltage for output regulation. Connect these pins
either to open-drain outputs with or without external pull-up
resistors or to active-pull-up outputs. VID4-VID12.5 have
50 μ A internal pull-up current sources that diminish to zero as
the voltage rises above the logic-high level. These inputs
can be pulled up as high as VCC plus 0.3V.
VDIFF, VSEN, and RGND
VSEN and RGND form the precision differential remote-
sense amplifier. This amplifier converts the differential
voltage of the remote output to a single-ended voltage
referenced to local ground. VDIFF is the amplifier ’s output
and the input to the regulation and protection circuitry.
Connect VSEN and RGND to the sense pins of the remote
load.
FB and COMP
Inverting input and output of the error amplifier respectively.
FB is connected to VDIFF through a resistor. A negative
current, proportional to output current is present on the FB
pin. A properly sized resistor between VDIFF and FB sets
the load line (droop). The droop scale factor is set by the
ratio of the ISEN resistors and the lower MOSFET r DS(ON) .
COMP is tied back to FB through an external R-C network to
compensate the regulator.
DAC and REF
The DAC output pin is the output of the precision internal
DAC reference. The REF input pin is the positive input of
the error amplifier. In typical applications, a 1k Ω , 1%
resistor is used between DAC and REF to generate a
precise offset voltage. This voltage is proportional to the
offset current determined by the offset resistor from OFS to
ground or VCC. A capacitor is used between REF and
ground to smooth the voltage transition during
Dynamic VID? operations.
PWM1, PWM2, PWM3, PWM4
Pulse-width modulation outputs. Connect these pins to the
PWM input pins of the Intersil driver IC. The number of
active channels is determined by the state of PWM3 and
PWM4. Tie PWM3 to VCC to configure for 2-phase
operation. Tie PWM4 to VCC to configure for 3-phase
operation.
ISEN1, ISEN2, ISEN3, ISEN4
Current sense inputs. The ISEN1, ISEN2, ISEN3, and
ISEN4 pins are held to a virtual ground such that a resistor
connected between them and the drain terminal of the
associated lower MOSFET will carry a current proportional
to the current flowing through the related channel. The
current is determined by the negative voltage developed
across the lower MOSFET’s r DS(ON) which is the channel
current scaled by the inverse of the r DS(ON) . The current is
used as a reference for channel balancing, protection, and
load-line regulation (via the FB pin). Inactive channels
should have their respective current sense inputs left open.
PGOOD
PGOOD is used as an indication of the end of soft-start per
the microprocessor specification. It is an open-drain logic
output that is low impedance until the soft start is
completed. It will be pulled low again once the undervoltage
point is reached.
OFS
The OFS pin provides a means to program a dc current for
generating an offset voltage at the REF input. The offset
current is generated via an external resistor and precision
internal voltage references. The polarity of the offset is
selected by connecting the resistor to GND or VCC. For no
offset, the OFS pin should be left unterminated.
9
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6556BCR-T | IC CTRLR MULTIPHASE VRM10 32-QFN |
| ISL6557ACB-T | IC REG CTRLR BUCK PWM VM 24-SOIC |
| ISL6558IR-T | IC REG CTRLR BUCK PWM 20-QFN |
| ISL6559CBZ-T | IC REG CTRLR BUCK PWM VM 28-SOIC |
| ISL6561CR-T | IC CTRLR PWM MULTIPHASE 40-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6556ACRZ | 功能描述:IC CTRLR MULTIPHASE VRM10 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6556ACRZ-T | 功能描述:IC CTRLR MULTIPHASE VRM10 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6556ACRZ-TR5208 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6556BCB | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6556BCB-T | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。