- 您现在的位置：买卖IC网 > Datasheet目录334 > ISL6615IBZ (Intersil)IC MOSFET DRVR SYNC HF 6A 8-SOIC Datasheet资料下载
参数资料
| 型号： | ISL6615IBZ |
| 厂商： | Intersil |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC MOSFET DRVR SYNC HF 6A 8-SOIC |
| 标准包装： | 980 |
| 配置： | 高端和低端，同步 |
| 输入类型： | PWM |
| 延迟时间： | 10ns |
| 电流 - 峰： | 2.5A |
| 配置数： | 1 |
| 输出数： | 2 |
| 高端电压 - 最大（自引导启动）： | 36V |
| 电源电压： | 6.8 V ~ 13.2 V |
| 工作温度： | -40°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
ISL6615
Schottky diode that is used in some systems for protecting
the load from reversed output voltage events.
In addition, more than 400mV hysteresis also incorporates
into the Tri-state shutdown window to eliminate PWM input
oscillations due to the capacitive load seen by the PWM
input through the body diode of the controller ’s PWM output
when the power-up and/or power-down sequence of bias
supplies of the driver and PWM controller are required.
Power-On Reset (POR) Function
During initial start-up, the VCC voltage rise is monitored.
Once the rising VCC voltage exceeds 6.4V (typically),
operation of the driver is enabled and the PWM input signal
takes control of the gate drives. If VCC drops below the
falling threshold of 5.0V (typically), operation of the driver is
disabled.
Q GATE is calculated to be 53nC for PVCC = 12V. We will
assume a 200mV droop in drive voltage over the PWM
cycle. We find that a bootstrap capacitance of at least
0.267μF is required. The next larger standard value
capacitance is 0.33μF. A good quality ceramic capacitor is
recommended.
1.6
1.4
1.2
1.0
0.8
0.6
Q GATE = 100nC
Pre-POR Overvoltage Protection
Prior to VCC exceeding its POR level, the upper gate is held
0.4
0.2
20nC
50nC
low and the lower gate is controlled by the overvoltage
protection circuits. The upper gate driver is powered from
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
PVCC and will be held low when a voltage of 2.75V or higher
is present on PVCC as VCC surpasses its POR threshold.
The PHASE is connected to the gate of the low side
MOSFET (LGATE), which provides some protection to the
microprocessor if the upper MOSFET(s) is shorted during
start-up, normal, or shutdown conditions. For complete
protection, the low side MOSFET should have a gate
threshold well below the maximum voltage rating of the
load/microprocessor.
Internal Bootstrap Device
Both drivers feature an internal bootstrap Schottky diode.
Simply adding an external capacitor across the BOOT and
PHASE pins completes the bootstrap circuit. The bootstrap
function is also designed to prevent the bootstrap capacitor
from overcharging due to the large negative swing at the
trailing-edge of the PHASE node. This reduces voltage
stress on the boot to phase pins.
The bootstrap capacitor must have a maximum voltage
rating above PVCC + 5V and its capacitance value can be
chosen from Equation 1:
Δ V BOOT_CAP (V)
FIGURE 2. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
Gate Drive Voltage Versatility
The ISL6615 provides the user with flexibility in choosing the
gate drive voltage for efficiency optimization. The ISL6615
ties the upper and lower drive rails together. Simply applying
a voltage from +4.5V up to 13.2V on PVCC sets both gate
drive rail voltages simultaneously, while VCC’s operating
range is from +6.8V up to 13.2V.
Power Dissipation
Package power dissipation is mainly a function of the
switching frequency (F SW ), the output drive impedance, the
external gate resistance, and the selected MOSFET’s
internal gate resistance and total gate charge. Calculating
the power dissipation in the driver for a desired application is
critical to ensure safe operation. Exceeding the maximum
allowable power dissipation level will push the IC beyond the
maximum recommended operating junction temperature of
+125°C. The maximum allowable IC power dissipation for
C BOOT_CAP ≥ --------------------------------------
Q GATE
Δ V BOOT_CAP
(EQ. 1)
the SO8 package is approximately 800mW at room
temperature, while the power dissipation capacity in the DFN
package, with an exposed heat escape pad, is more than
Q GATE = ------------------------------------ ? N Q1
Q G1 ? PVCC
V GS1
where Q G1 is the amount of gate charge per upper MOSFET at
V GS1 gate-source voltage and N Q1 is the number of control
MOSFETs. The Δ V BOOT_CAP term is defined as the allowable
droop in the rail of the upper gate drive.
As an example, suppose two IRLR7821 FETs are chosen as
the upper MOSFETs. The gate charge, Q G , from the data
sheet is 10nC at 4.5V (V GS ) gate-source voltage. Then the
7
1.5W. The DFN package is more suitable for high frequency
applications. See “Layout Considerations” on page 8 for
thermal transfer improvement suggestions. When designing
the driver into an application, it is recommended that the
following calculation is used to ensure safe operation at the
desired frequency for the selected MOSFETs. The total gate
drive power losses due to the gate charge of MOSFETs and
the driver ’s internal circuitry and their corresponding average
driver current can be estimated with Equations 2 and 3,
respectively.
FN6481.0
April 24, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6620ACBZ | IC SYNC RECT MOSFET DRVR 8-SOIC |
| ISL6622AIBZ | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| ISL6622CBZ-T | IC MOSFET DVR SYNC BUCK 8-SOIC |
| ISL6801ABT | IC DRIVER HISIDE BOOTSTRAP 8SOIC |
| ISL78100ARZ | IC LED DRIVER AUTOMOTIVE 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6615IBZ-T | 功能描述:IC MOSFET DRVR SYNC HF 6A 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| ISL6615IRZ | 功能描述:IC MOSFET DRVR SYNC HF 6A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| ISL6615IRZ-T | 功能描述:IC MOSFET DRVR SYNC HF 6A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| ISL6617CRZ | 功能描述:功率驱动器IC PHS SPLITTER COM 10LD 3X3 RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| ISL6617CRZ-T | 功能描述:功率驱动器IC PHS SPLITTER COM 10LD 3X3 RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。