- 您现在的位置：买卖IC网 > PDF目录15524 > ISL6742AAZA (Intersil)IC REG CTRLR PWM CM/VM 16-QSOP PDF资料下载
参数资料
| 型号： | ISL6742AAZA |
| 厂商： | Intersil |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM/VM 16-QSOP |
| 标准包装： | 98 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 4 |
| 频率 - 最大： | 2MHz |
| 占空比： | 100% |
| 电源电压： | 9 V ~ 16 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1243 (CN2011-ZH PDF) |
ISL6742
The average current signal on IOUT remains accurate
ISL6742
7 CS
provided that the output inductor current is continuous (CCM
operation). Once the inductor current becomes discontinuous
(DCM operation), IOUT represents 1/2 the peak inductor
current rather than the average current. This occurs because
the sample and hold circuitry is active only during the on-time
of the switching cycle. It is unable to detect when the inductor
current reaches zero during the off-time.
If average overcurrent limit is desired, IOUT may be used
with the available error amplifier of the ISL6742. Typically,
IOUT is divided down and filtered as required to achieve the
150mV TO
1000mV
C10
R6
1
2 VERR
3
4
5 FB -
0.6V +
6
S&H
4x
8 IOUT
R5
1
6
1
5
1
4
1
3
1
2
1
1
1
0
9
desired amplitude. The resulting signal is input to the current
error amplifier (IEA). The IEA is similar to the voltage EA
found in most PWM controllers, except it cannot source
R4
current. Instead, VERR has a separate internal 1mA pull-up
current source.
FIGURE 7. AVERAGE OVERCURRENT IMPLEMENTATION
Configure the IEA as an integrating (Type I) amplifier using
the internal 0.6V reference. The voltage applied at FB is
integrated against the 0.6V reference. The resulting signal,
The current EA crossover frequency, assuming R6 >>
(R4||R5), is expressed in Equation 7:
f CO = -----------------------------------
VERR, is applied to the PWM comparator where it is
compared to the sawtooth voltage on RAMP. If FB is less
1
2 π ? R6 ? C10
Hz
(EQ. 7)
than 0.6V, the IEA will be open loop (can’t source current),
VERR will be at a level determined by the voltage loop, and
the duty cycle is unaffected. As the output load increases,
IOUT will increase, and the voltage applied to FB will
increase until it reaches 0.6V. At this point the IEA will
reduce VERR as required to maintain the output current at
the level that corresponds to the 0.6V reference. When the
output current again drops below the average current limit
threshold, the IEA returns to an open loop condition, and the
duty cycle is again controlled by the voltage loop.
The average current control loop behaves much the same
as the voltage control loop found in typical power supplies
except it regulates current rather than voltage.
The EA available on the ISL6742 may also be used as the
voltage EA for the voltage feedback control loop rather than
the current EA as described previously. An external op amp
may be used as either the current or voltage EA providing
the circuit is not allowed to source current into VERR. The
external EA must only sink current, which may be
accomplished by adding a diode in series with its output.
The 4x gain of the sample and hold buffer allows a range of
150mV to 1000mV peak on the CS signal, depending on the
resistor divider placed on IOUT. The overall bandwidth of the
average current loop is determined by the integrating current
EA compensation and the divider on IOUT.
11
where f CO is the crossover frequency. A capacitor in parallel
with R4 may be used to provide a double-pole roll-off.
The average current loop bandwidth is normally set to be
much less than the switching frequency, typically less than
5kHz and often as slow as a few hundred hertz or less. This is
especially useful if the application experiences large surges.
The average current loop can be set to the steady state
overcurrent threshold and have a time response that is longer
than the required transient. The peak current limit can be set
higher than the expected transient so that it does not interfere
with the transient, but still protects for short-term larger faults.
In essence, a 2-stage overcurrent response is possible.
The peak overcurrent behavior is similar to most other PWM
controllers. If the peak current exceeds 1V, the active output
pulse is terminated immediately.
If voltage-mode control is used in a bridge topology, it should
be noted that peak current limit results in inherently unstable
operation. DC blocking capacitors used in voltage-mode
bridge topologies become unbalanced, as does the flux in
the transformer core. The average overcurrent circuitry
prevents this behavior by maintaining symmetric duty cycles
for each half-cycle. If the average current limit circuitry is not
used, a latching overcurrent shutdown method using
external components is recommended.
The CS to output propagation delay is increased by the
leading edge blanking (LEB) interval. The effective delay is
the sum of the two delays and is 130ns maximum.
Voltage Feed-Forward Operation
Voltage feed-forward is a technique used to regulate the
output voltage for changes in input voltage without the
FN9183.2
October 31, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J5D-EY | CONVERTER MOD DC/DC 85V 50W |
| RCM18DTAT | CONN EDGECARD 36POS R/A .156 SLD |
| 0819-92K | COIL RF 680UH MOLDED UNSHIELDED |
| RSM08DTAN | CONN EDGECARD 16POS R/A .156 SLD |
| VI-J5B-EY | CONVERTER MOD DC/DC 95V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6742AAZA-T | 功能描述:IC REG CTRLR PWM CM/VM 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AABZ | 功能描述:IC REG CTRLR PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AABZ-T | 功能描述:IC REG CTRLR PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AAUZ | 功能描述:IC REG CTRLR PWM VM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AAUZ-T | 功能描述:IC REG CTRLR PWM VM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。