- 您现在的位置：买卖IC网 > PDF目录15524 > ISL6742AAZA (Intersil)IC REG CTRLR PWM CM/VM 16-QSOP PDF资料下载
参数资料
| 型号： | ISL6742AAZA |
| 厂商： | Intersil |
| 文件页数： | 9/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM/VM 16-QSOP |
| 标准包装： | 98 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 4 |
| 频率 - 最大： | 2MHz |
| 占空比： | 100% |
| 电源电压： | 9 V ~ 16 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1243 (CN2011-ZH PDF) |
ISL6742
OUTAN and OUTBN - These outputs are the complements
of OUTA and OUTB, respectively. These outputs are suitable
for control of synchronous rectifiers. The phase relationship
between each output and its complement is set by a control
voltage applied to VADJ.
VADJ - A 0V to 5V control voltage applied to this input sets
the relative delay or advance between OUTA/OUTB and
OUTAN/OUTBN.
Voltages below 2.425V result in OUTAN/OUTBN being
advanced relative to OUTA/OUTB. Voltages above 2.575V
result in OUTAN/OUTBN being delayed relative to
OUTA/OUTB. A voltage of 2.50V ±75mV results in zero
phase difference. A weak internal 50% divider from VREF
results in no phase delay if this input is left floating.
The range of phase delay/advance is either zero or 40ns to
300ns with the phase differential increasing as the voltage
deviation from 2.5V increases. The relationship between the
control voltage and phase differential is non-linear. The gain
( Δ t/ Δ V) is low for control voltages near 2.5V and rapidly
increases as the voltage approaches the extremes of the
control range. This behavior provides the designer increased
accuracy when selecting a shorter delay/advance duration.
When the PWM outputs are delayed relative to the SR
outputs (VADJ < 2.425V), the delay time should not exceed
90% of the deadtime as determined by RTD and CT.
IOUT - Output of the 4x buffer amplifier of the sample and
hold circuitry that captures and averages the CS signal.
RAMP - This is the input for the sawtooth waveform for the
PWM comparator. The RAMP pin is shorted to GND at the
termination of the PWM signal. A sawtooth voltage
waveform is required at this input. For current-mode control
complements of OUTA and OUTB, respectively, go to 100%
duty cycle when this occurs.
SS - Connect the soft-start timing capacitor between this pin
and GND to control the duration of soft-start. The value of
the capacitor determines the rate of increase of the duty
cycle during start-up. Although no minimum value of
capacitance is required, it is recommended that a value of at
least 100pF be used for noise immunity.
SS may also be used to inhibit the outputs by grounding
through a small transistor in an open collector/drain
configuration.
Functional Description
Features
The ISL6742 PWM is an excellent choice for low cost bridge
and push-pull topologies in applications requiring accurate
duty cycle and deadtime control. With its many protection
and control features, a highly flexible design with minimal
external components is possible. Among its many features
are current- or voltage-mode control, adjustable soft-start,
peak and average overcurrent protection, thermal protection,
synchronous rectifier outputs with variable delay/advance
timing, and adjustable oscillator frequency.
Oscillator
The ISL6742 oscillator, with a programmable frequency
range to 2MHz, is set with only an external resistor and
capacitor.
The switching period is the sum of the timing capacitor
charge and discharge durations. The charge duration is
determined by CT and a fixed 200μA internal current source.
The discharge duration is determined by RTD and CT.
t C ≈ 11.5 ? 10 ? CT
this pin is connected directly to CS and the current loop
feedback signal is applied to both inputs. For voltage-mode
3
S
(EQ. 1)
control, the oscillator sawtooth waveform may be buffered
and used to generate an appropriate signal, or RAMP may
be connected to the input voltage through an RC network for
t D ≈ ( 0.06 ? RTD ? CT ) + 50 ? 10
– 9
S
(EQ. 2)
voltage feed forward control, or RAMP may be connected to
t SW = t C + t D = ------------
VREF through an RC network to produce the desired
sawtooth waveform.
1
F SW
S
(EQ. 3)
FB - FB is the inverting input to the error amplifier (EA). The
amplifier may be used as the error amplifier for voltage
feedback or used as the average current limit amplifier (IEA).
If the amplifier is not used, FB should be grounded.
VERR - The VERR pin is the output of the error amplifier and
controls the inverting input of the PWM comparator.
Feedback compensation components connect between
VERR and FB. There is a nominal 1mA pull-up current
source connected to VERR. Soft-start is implemented as a
voltage clamp on the VERR signal.
The outputs, OUTA and OUTB, reduce to 0% duty cycle
when VERR is pulled below 0.6V. OUTAN and OUTBN, the
9
where t C and t D are the charge and discharge times,
respectively, t SW is the oscillator period, and F SW is the
oscillator frequency. Since the ISL6742 is a double-ended
controller, one output switching cycle requires two oscillator
cycles. The actual charge and discharge times will be slightly
longer than calculated due to internal propagation delays of
approximately 10ns/transition. This delay adds directly to the
switching duration, but also causes slight overshoot of the
timing capacitor peak and valley voltage thresholds,
effectively increasing the peak-to-peak voltage on the timing
capacitor. Additionally, if very low discharge currents are
used, there will be increased error due to the input
impedance at the CT pin.
FN9183.2
October 31, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J5D-EY | CONVERTER MOD DC/DC 85V 50W |
| RCM18DTAT | CONN EDGECARD 36POS R/A .156 SLD |
| 0819-92K | COIL RF 680UH MOLDED UNSHIELDED |
| RSM08DTAN | CONN EDGECARD 16POS R/A .156 SLD |
| VI-J5B-EY | CONVERTER MOD DC/DC 95V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6742AAZA-T | 功能描述:IC REG CTRLR PWM CM/VM 16-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AABZ | 功能描述:IC REG CTRLR PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AABZ-T | 功能描述:IC REG CTRLR PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AAUZ | 功能描述:IC REG CTRLR PWM VM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6744AAUZ-T | 功能描述:IC REG CTRLR PWM VM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。