参数资料
| 型号： | ISL78322ARZ |
| 厂商： | Intersil |
| 文件页数： | 15/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ DL 12-DFN |
| 标准包装： | 75 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.8 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 2.25MHz |
| 电流 - 输出： | 2A，1.7A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-VFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-DFN（4x3） |
ISL78322
CLOCK
PWM
16 CYCLES
PFM
PFM CURRENT LIMIT
I L
LOAD CURRENT
0
NOMINAL +1.5 %
V OUT
NOMINAL
FIGURE 45. SKIP MODE OPERATION WAVEFORMS
Positive and Negative Overcurrent Protection
CSA1 and CSA2 are used to monitor output 1 and output 2
channels respectively. The overcurrent protection is realized by
monitoring the CSA_ output with the OCP threshold logic, as
shown in the “Block Diagram” on page 3. The current sensing
circuit has a gain of 0.32V/A, from the P-MOSFET current to the
CSA_ output. When the CSA_ output reaches the threshold of
1.25V for Channel 1 and 1.1V for Channel 2, the OCP comparator
is tripped to turn off the P-MOSFET immediately. The overcurrent
function protects the switching converter from a shorted output by
monitoring the current flowing through the upper MOSFETs.
Upon detection of an overcurrent condition, the upper MOSFET
will be immediately turned off and will not be turned on again
until the next switching cycle. Upon detection of the initial
overcurrent condition, the Overcurrent Fault Counter is set to 1
and the Overcurrent Condition Flag is set from LOW to HIGH. If,
on the subsequent cycle, another overcurrent condition is
detected, the OC Fault Counter will be incremented. If there are
17 sequential OC fault detections, the regulator will be shut down
under an Overcurrent Fault Condition. An Overcurrent Fault
Condition will result with the regulator attempting to restart in a
hiccup mode with the delay between restarts being 4 soft-start
periods. At the end of the fourth soft-start wait period, the fault
counters are reset and soft-start is attempted again. If the
overcurrent condition goes away prior to the OC Fault Counter
reaching a count of four, the Overcurrent Condition Flag will set
back to LOW.
In the event that the inductor current reaches -1.6A, the part
enters Negative Overcurrent Protection. At this point, all
switching stops and the part enters tri-state mode while the
pull-down FET is discharging the output until it reaches normal
regulation voltage, then the IC restarts switching.
PG
The power-good signal (PG), monitors both of the output
channels. When powering up, the open-collector Power-On-Reset
output holds low for about 1ms after V O1 and V O2 reaches the
preset voltages. The PG output also serves as a 1ms delayed
power-good signal. If one of the outputs is disabled, then PG only
monitors the active channels. There is an internal 1M Ω pull-up
resistor.
15
UVLO
When the input voltage is below the undervoltage lock-out (UVLO)
threshold, the regulator is disabled.
Enable
The enable (EN1, EN2) input allows the user to control the turning
on or off the regulator for purposes such as power-up
sequencing. The regulator is enabled, there is typically a 600μs
delay for waking up the bandgap reference and the soft start-up
begins.
Soft Start-Up
The soft start-up eliminates the in-rush current during start-up.
The soft-start block outputs a ramp reference to both the voltage
loop and the current loop. The two ramps limit the inductor
current rising speed as well as the output voltage speed so that
the output voltage rises in a controlled fashion.
At the very beginning of the start-up, the feedback voltage is less
than 0.2V; hence the PWM operating frequency is 1/3 of the
normal frequency. In forced PWM mode, the IC will continue to
start-up in PFM mode to support pre-biased load applications.
During soft-start period, the device will operate in tri-state mode,
with both high-side and low-side drivers off to prevent negative
inductor current flow in output stage. Once soft-start is
completed, the drivers will allow negative inductor current only if
SYNC is set to low for PWM mode. By this time, the output should
reach regulation.
Discharge Mode (Soft-Stop)
When a transition to shutdown mode occurs, or the output
undervoltage fault latch is set, the outputs discharge to GND
through an internal 100 Ω switch.
Power MOSFETs
The power MOSFETs are optimized for best efficiency. The
ON-resistance for the P-MOSFET is typically 100m Ω and the
ON-resistance for the N-MOSFET is typical 90m Ω .
FN7908.1
January 14, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| ISL8009AIRZ-T7A | IC REG BUCK SYNC ADJ 1.5A 8DFN |
| ISL80101AIRAJZ | IC REG LDO ADJ 1A 10DFN |
| ISL80101IRAJZ-TK | IC REG LDO ADJ 1A 10DFN |
| ISL80103IRAJZ | IC REG LDO ADJ 3A 10DFN |
| ISL8010IUZ | IC REG BUCK SYNC ADJ 0.6A 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL78322ARZ-T | 功能描述:IC REG BUCK SYNC ADJ DL 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL78322ARZ-TR5303 | 制造商:Intersil Corporation 功能描述: |
| ISL78419 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Integrated Automotive TFT-LCD Power Supply Regulator |
| ISL78419ARZ | 功能描述:其他电源管理 TFT-LCD POWER SUPPLY AUTOMOTIVE RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| ISL78419ARZ-T | 制造商:Intersil Corporation 功能描述:ISL78419ARZ INTEGRATED AUTOMOTIVE TFT-LCD POWER SUPPLY REGUL - Tape and Reel 制造商:Intersil Corporation 功能描述:IC TFT-LCD PS REGULATOR 28QFN 制造商:Intersil 功能描述:TFT-LCD POWER SUPPLY AUTOMOTIVE |
发布紧急采购，3分钟左右您将得到回复。