- 您现在的位置：买卖IC网 > PDF目录13603 > ISL8016IRAJZ-T (Intersil)IC REG BUCK SYNC ADJ 6A 20QFN PDF资料下载
参数资料
| 型号： | ISL8016IRAJZ-T |
| 厂商： | Intersil |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 20QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 525kHz ~ 3.9MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-QFN（3x4） |
ISL8016
Negative Current Protection
Similar to the overcurrent, the negative current protection is
realized by monitoring the current across the low-side N-FET, as
shown in Figure 4. When the valley point of the inductor current
reaches -3A for 4 consecutive cycles, both P-FET and N-FET are off.
The 100 ? in parallel to the N-FET will activate discharging the
output into regulation. The control will begin to switch when output
is within regulation. The regulator will be in PFM for 20μs before
Figure 38 is a comparison between measured and calculated
output soft-start time versus Css capacitance.
18
15
12
switching to PWM if necessary.
PG
PG is an open-drain output of a window comparator that
continuously monitors the buck regulator output voltage. PG is
actively held low when EN is low and during the buck regulator
9
6
3
SS (ms)
MEASUREMENT
SS (ms)
CALCULATION
soft-start period. After 1ms delay of the soft-start period, PG
becomes high impedance as long as the output voltage is within
0
0
8
16
24
32
40
48
nominal regulation voltage set by VFB. When VFB drops 15%
below or raises 0.8V above the nominal regulation voltage, the
ISL8016 pulls PG low. Any fault condition forces PG low until the
fault condition is cleared by attempts to soft-start. For logic level
output voltages, connect an external pull-up resistor, R 1 , between
PG and VIN. A 100k ? resistor works well in most applications.
UVLO
When the input voltage is below the undervoltage lock-out (UVLO)
threshold, the regulator is disabled.
Soft Start-Up
The soft start-up reduces the in-rush current during the start-up.
The soft-start block outputs a ramp reference to the input of the
error amplifier. This voltage ramp limits the inductor current as
well as the output voltage speed so that the output voltage rises
in a controlled fashion. When VFB is less than 0.1V at the
beginning of the soft-start, the switching frequency is reduced to
200kHz so that the output can start-up smoothly at light load
condition. During soft-start, the IC operates in the SKIP mode to
support pre-biased output condition.
Tie SS to SGND for an internal soft-start of approximately 1ms.
Connect a capacitor from SS to SGND to adjust the soft-start
time. This capacitor, along with an internal 1.6μA current source
sets the soft-start interval of the converter, t SS .
C SS (nF)
FIGURE 38. SOFT-START TIME vs C SS
Enable
The enable (EN) input allows the user to control the turning on or
off of the regulator for purposes such as power-up sequencing.
When the regulator is enabled, there is typically a 600μs delay
for waking up the bandgap reference and then the soft start-up
begins.
Discharge Mode (Soft-Stop)
When a transition to shutdown mode occurs or the VIN UVLO is
set, the outputs discharge to GND through an internal 100 ?
switch. The discharge mode is disabled if SS is tied to an external
capacitor.
Power MOSFETs
The power MOSFETs are optimized for best efficiency. The
ON-resistance for the P-FET is typically 30m ? and the
ON-resistance for the N-FET is typically 20m ? .
100% Duty Cycle
The ISL8016 features 100% duty cycle operation to maximize
the battery life. When the battery voltage drops to a level that the
C SS [ μ F ] = 3.33 ? t SS [ s ]
(EQ. 3)
ISL8016 can no longer maintain the regulation at the output, the
regulator completely turns on the P-FET. The maximum dropout
C SS must be less than 33nF to insure proper soft-start reset after
fault condition.
17
voltage under the 100% duty-cycle operation is the product of the
load current and the ON-resistance of the P-FET.
Thermal Shutdown
The ISL8016 has built-in thermal protection. When the internal
temperature reaches +150°C, the regulator is completely shut
down. As the temperature drops to +125°C, the ISL8016 resumes
operation by stepping through the soft-start.
FN7616.1
May 5, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| SCRH123-6R2 | INDUCTOR SMD 6.2UH 6.70A 100KHZ |
| ISL8016IR33Z-T | IC REG BUCK SYNC 3.3V 6A 20QFN |
| VI-J50-EX-F2 | CONVERTER MOD DC/DC 5V 75W |
| ISL8016IR25Z-T | IC REG BUCK SYNC 2.5V 6A 20QFN |
| ISL8016IR18Z-T | IC REG BUCK SYNC 1.8V 6A 20QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8016IRAJZ-T7A | 功能描述:直流/直流开关转换器 6A ADJ VOUT LW QUIES CENT CUR SYNC BUCK RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| ISL8022 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 2A/1.7A Low Quiescent Current 2.25MHz High Efficiency Synchronous |
| ISL8022EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL8022 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8022EVAL2Z | 功能描述:EVAL BOARD 2 FOR ISL8023 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8022IRZ | 功能描述:直流/直流开关调节器 DL CH 2 25MHZ 2 0 A & 1 7ASYNCHG 4X3 1 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。